background image

Operating Guidelines 

Edge MAXX

3-4

3.2  Operating Controls

All operating controls are externally mounted 

on the machine and most are clearly marked with 

nameplates.

References to these functions are capitalized 

in this manual for easy identification. Detailed 

descriptions  are  given  in  the  following 

paragraphs.

Most of these controls are located at the front of 

the machine. There are duplicate sets of operator 

controls as well as non-duplicated controls.

Front Controls

Controls at the front of the unit include (Figure 

3-7):

START/STOP buttons (A)
SAFETY STOP buttons (B)
STAIN REJECT (option) button (C)
TEAR REJECT (option) button (D)
CHI Panel (E)
INTERCONNECTED STOP CIRCUIT 

(option) indicator lights (F)
Pacing Lights (option) (G)

START/STOP button (A):

Initiate and pause general machine operation. 

Each station has a set. The green

 

Start button 

starts all moving parts while the square red

 

Stop 

button pauses operation of the unit.

During normal operation, the integrated lamp 

glows steadily when the unit is running. The lamp 

flashes when either a red station Stop button or a 

red safety STOP button is pressed.






Figure 3-7:  Controls located at the front of the feeder unit.

A

A

B

B

C

C

D

D

E

F

G

TOC

INDEX

Summary of Contents for Edge MAXX

































































































































































































































































































Reviews: