background image

80kg tow behind broadcast spreader

mODEL NO: 

spb80t.V2

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions, 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  saFetY

 

 

9

   Ensure that the spreader is in sound condition and good working order before use.

 

9

   Ensure that the operator is fully trained and competent to operate the prime mover before attaching and using the spreader.

 

9

   Ensure that all chemical safety instructions are adhered to when handling products for use in the spreader. A full range of personal safety  

  equipment is available from your Sealey stockist.

 

9

   Always distribute the load evenly.

 

9

   Ensure all non essential personnel keep a safe distance when the spreader is in use.

 

9

   Replace or repair damaged parts. Use only recommended parts. Unauthorised parts may be dangerous and will invalidate the warranty.

 

9

   Keep hands and feet away from moving parts.

 

8

  

do not

 overload the spreader - see Specification.

 

8

  

do not

 leave unattended, especially when loaded, unless the wheels are chocked or the spreader is otherwise secured.

 

8

  

do not

 allow anyone to ride on the spreader.

 

8

  

do not

 allow untrained personnel to use the spreader. 

do not

 allow children to use the spreader.

 

8

  

do not

 use the spreader for purposes other than for which it is designed.

 

8

  

do not 

operate the spreader when you

 

are tired or under the influence of alcohol, drugs or intoxicating medicines.

 

9

   When  loaded, 

do not 

operate the spreader over edges, rough surfaces etc. where the spreader is at risk of overturning.

 

 

‰

  

warning! 

Failure to comply with these instructions may result in damage to spreader or other property and/or personal injury.

2.  introduction

manufactured with a strong tubular steel frame and polypropylene dispensing hopper. Pin hitch design attaches to ride-on lawnmowers, can be 

converted to ball hitch using model No. TB36*. Fitted with aluminium gear, rain cover, pneumatic tyres and adjustable feed system. Includes 

hopper screen to ease spreader flow and filter out unwanted contaminants. Sprays in 360° motion to cover a large area. Suitable for a variety of 

horticultural agents including grit, seed, salt, fertilizer and weed killer.

* Some modification may be required

3.  speciFication

model no ..............................................................

SPB80T.V2

Capacity (volume) ............................................................ 88L

Dimensions (W x D x H) ........................

880 x 1350 x 965mm

Spread ........................................................................3-3.6m

4.  contents

Original Language Version

© Jack Sealey Limited

Refer to

instruction 

manual

S

PB80T.V2 | Issue:1  11/11/19

Summary of Contents for SPB80T.V2






Reviews: