Chevrolet Express 2012 Owner'S Manual Download Page 323 | Manualshive

Page: 323 / 404

background image

Black plate (73,1)

Chevrolet Express Owner Manual - 2012 - crc - 11/11/11

Vehicle Care

10-73

Rear Alternative Position

(Diesel Vehicles)

4. Position the jack under the

vehicle, as shown.

The front position jacking point is
on the frame. The rear position
jacking point is on the rear axle.

If the exhaust system interferes
in the jack location in the rear
axle, such as in Diesel vehicles,
place the jack (A) on the rear
axle between the axle housing
and the shock absorber bracket

in order to avoid any
interference with the exhaust
pipe (B).

{

WARNING

Getting under a vehicle when it is
jacked up is dangerous. If the
vehicle slips off the jack you could
be badly injured or killed. Never
get under a vehicle when it is
supported only by a jack.

{

WARNING

Raising the vehicle with the jack
improperly positioned can
damage the vehicle and even
make the vehicle fall. To help
avoid personal injury and vehicle
damage, be sure to fit the jack lift
head into the proper location
before raising the vehicle.

5. Turn the wheel wrench

clockwise to raise the vehicle.
Raise the vehicle far enough off
the ground so there is enough
room for the spare tire to fit.

6. Remove all the wheel nuts.

7. Take flat tire off of the mounting

surface.

«
...
321
322
323
324
325
...
»

Summary of Contents for Express 2012





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express 2012

Brand: Haibang Pages: 6

Brand: AC Schnitzer Pages: 20

Brand: XTC Pages: 4

Q Access Alpha GSE 2023

Brand: Q Mobility Group Pages: 9

Brand: Voxoa Pages: 48

Brand: Volvo Pages: 266

Brand: KEKO Pages: 3

Brand: Movon Pages: 43

Brand: ULTIMATE SPEED Pages: 32

Brand: Chevrolet Pages: 441

Brand: POOL-LINE Pages: 2

Brand: Skoda Pages: 2

CF-UFORCE-DRW01

Brand: FALCON RIDGE Pages: 6

Brand: Whispbar Pages: 14

Brand: BMW Pages: 278

Brand: Subaru Pages: 399

Brand: travall Pages: 4

Brand: Edelbrock Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands