Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 139 / 372

background image

Air Bag Readiness Light

There is an air bag readiness light on the instrument
panel, which shows AIR BAG. The system checks
the air bag’s electrical system for malfunctions. The light
tells you if there is an electrical problem. The system
check includes the air bag modules, and the crash
sensing and diagnostic module. For more information
on the air bag system, see

Supplemental Restraint

System (SRS) on page 1-54.

This light will come on
when you start your
vehicle, and it will flash
for a few seconds.
Then the light should go
out. This means the
system is ready.

If the air bag readiness light stays on after you start the
vehicle or comes on when you are driving, your air
bag system may not work properly. Have your vehicle
serviced right away.

{

CAUTION:

If the air bag readiness light stays on after you
start your vehicle, it means the air bag system
may not be working properly. The air bags in
your vehicle may not inflate in a crash, or they
could even inflate without a crash. To help
avoid injury to yourself or others, have your
vehicle serviced right away if the air bag
readiness light stays on after you start your
vehicle.

The air bag readiness light should flash for a few
seconds when you turn the ignition key to ON. If the
light doesn’t come on then, have it fixed so it will
be ready to warn you if there is a problem.

3-27

«
...
137
138
139
140
141
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: RAM Pages: 116

Brand: Safe Fleet Pages: 38

Brand: ECS Electronics Pages: 16

StreetLine Series

Brand: SAAS Pages: 4

Brand: JANE Pages: 58

Brand: ULTIMATE SPEED Pages: 50

Brand: E&G Classics Pages: 2

Brand: v.LOGiC Pages: 22

Brand: rockymounts Pages: 6

Brand: PUTCO Pages: 2

ESCALADE ESV 2005

Brand: Cadillac Pages: 482

Brand: curt Pages: 4

2000 Accord Sedan

Brand: Honda Pages: 320

Brand: Edelbrock Pages: 2

Brand: Hudson Pages: 77

Brand: iSimple Pages: 12

2001 Accord Sedan

Brand: Honda Pages: 372

Brand: Imiola HAK-POL Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands