background image

 

 

 

Page 14

 

 

 

 

 
 
 
 

 
 

 

In the event that a problem develops with your CGLS product, 

DO NOT 

attempt to perform any service on the 

unit without first contacting the CGLS Customer Service Department at 1-800-843-1794. 

Unauthorized 

servicing may void the warranty. 

CGLS will supply information on minor repairs upon request. In any 

correspondence to CGLS concerning this unit, please include the catalog number (CLS-1200-2CH) and the serial 
number, which may be found on the bottom of the unit. 

 

WARNING: POTENTIAL SHOCK HAZARD EXISTS WHEN TOP COVER IS 
REMOVED. 
DISCONNECT POWER CORD BEFORE SERVICING. 

 

1.

 

Contact CGLS for troubleshooting assistance. 
 

 

Preventive Maintenance Suggestions 

1.

 

Periodically check connection of Pt100 sensor for corrosion, clean if necessary.  

2.

 

Cleaning - keep the instrument dry and clean.  The unit must be powered off and unplugged before 
cleaning. Do not use abrasive cleaning agents.  The exterior should be wiped with a damp cloth with 
water and 70% alcohol if needed.  Ensure unit is completely dry before plugging in and turning on. 

3.

 

Periodically check power cords for any tears or cracks, replace if necessary. 

 

 
 
 
 
 
 

 

 

 
 
 

 

 

 

 

 

 

 

    Service/Maintenance 

    CGLS WARRANTY AND LIMITATION OF LIABILITY 

Chemglass, Chemglass Life Sciences, Warranty and 

Limitation of Liability 

Warranty: 

Chemglass, Inc. guarantees this unit against defects in material and workmanship for a period of one year from the date of 

purchase.  If the unit should malfunction, it must be returned for evaluation.  If the unit is determined to have a defect in 
materials or workmanship, then it will be repaired or replaced at no charge.  Tampering with the unit or damage resulting from 
excessive current, heat, moisture, vibration, corrosive materials, or misuse will void this warranty.  Programming changes or 
reconfigurations are not covered under warranty.  CGLS shall not be responsible to the original purchaser or any other party or 
parties for bodily or property loss, damages, or injuries of any kind or nature through either direct or indirect use of the 
product. 

 

 

Return Authorization: 

CGLS must authorize any return of product.  Please contact a customer service representative via the correspondence listed 
below to obtain a Return Merchandise Authorization (RMA) number.  The purchaser is responsible for all packing and shipping 
to CGLS.  If the equipment or material came in contact or was proximate to any biological organism, toxic or corrosive material, 
or any agent reasonably deemed to be potentially harmful, it must be cleaned and decontaminated prior to receipt by CGLS.  
The purchaser is obligated to disclose fully in writing, the cleaning and decontamination method.  We reserve the right not to 
accept any unauthorized or potentially harmful shipment. 

 

 

 
 

Correspondence: 

Chemglass Life Sciences 
3800 North Mill Rd. 
Vineland, NJ 08360 
USA 
 

 

 

Phone: 800-843-1794 
Email: 

[email protected]

 

Web: 

www.cglifesciences.com

 

Summary of Contents for CHEMcell CLS-1200-2CH















Reviews: