CHD 8-427, Owner'S Manual, Page: 12 / 32

Korg Polysix MIDI Interface Korg Polysix MIDI Interface Korg Polysix MIDI Interface Korg Polysix MIDI Interface
P6 P6 P6 P6----M M M M Owner‘s Owner‘s Owner‘s Owner‘s Manual Manual Manual Manual
8 88 8----427 / v. 1.00 427 / v. 1.00 427 / v. 1.00 427 / v. 1.00
Copyright © 2021 CHD Elektroservis. All rights reserved.
No part of this publication may be reproduced in any form without the written permission of CHD Elektroservis.
12
12 12
12
•
2 2 2 2
Æ
Æ Æ
Æ
Fixed Fixed Fixed Fixed ---- Smooth Start: Smooth Start: Smooth Start: Smooth Start: The same as the “Fixed” mode but VCF modulation fades in for approx. 1,3 second.
•
3 3 3 3
Æ Æ Æ Æ
MIDI MIDI MIDI MIDI ---- Smooth Start: Smooth Start: Smooth Start: Smooth Start: The same as the “MIDI” mode but VCF modulation fades in for approx. 1,3 second.
Rema Rema Rema Remark: rk: rk: rk: Both Smooth Start modes (2 and 3) are allowed only for MIDI Notes. They don't work with instrument's
own keyboard!
Fig. 10 Fig. 10 Fig. 10 Fig. 10 – –– – VCF LFO synchronization modes VCF LFO synchronization modes VCF LFO synchronization modes VCF LFO synchronization modes
4.2.9
4.2.9 4.2.9
4.2.9 VCF LFO RATE (CC #24)
VCF LFO RATE (CC #24) VCF LFO RATE (CC #24)
VCF LFO RATE (CC #24)
The parameter sets the rate of the additional software LFO. It can be temporarily changed by MIDI CC Nr. 24 -
see chapter 5.1.2.2.
The parameter value is 0 to 127. Table 10 in chapter 6.5 shows conversion of the parameter value to the rate
for both “Fixed” and “MIDI” synchronization modes choosen by VCF LFO SYNC parameter.
4.2.10
4.2.10 4.2.10
4.2.10 VCF LFO DELAY (CC #25)
VCF LFO DELAY (CC #25) VCF LFO DELAY (CC #25)
VCF LFO DELAY (CC #25)
This parameter is active only for MIDI Notes. It doesn't work with instrument's keyboard!
The parameter sets the delay before launching the additional LFO after a key is pressed. It can be temporarily
changed by MIDI CC Nr. 25 - see chapter 5.1.2.2.
The parameter value is 0 to 127. Table 11 in chapter 6.5 shows conversion of the parameter value to the delay
time for both “Fixed” and “MIDI” synchronization modes choosen by VCF LFO SYNC parameter.
4.2.11
4.2.11 4.2.11
4.2.11 VCF LFO AMOUNT (CC #26)
VCF LFO AMOUNT (CC #26) VCF LFO AMOUNT (CC #26)
VCF LFO AMOUNT (CC #26)
The parameter sets basic VCF modulation depth by the additional software LFO. It can be temporarily changed
by MIDI CC Nr. 26 - see chapter 5.1.2.2.
The parameter value is 0 to 127. For 0 value, the VCF is not affected by the additional LFO. For 127 value, the
VCF modulation depth is maximal.
4.2.12
4.2.12 4.2.12
4.2.12 VCF LFO MODULATION WHEEL (CC #27)
VCF LFO MODULATION WHEEL (CC #27) VCF LFO MODULATION WHEEL (CC #27)
VCF LFO MODULATION WHEEL (CC #27)
Fig. 11 Fig. 11 Fig. 11 Fig. 11 – –– – VCF LFO mod. depth by CC #1 VCF LFO mod. depth by CC #1 VCF LFO mod. depth by CC #1 VCF LFO mod. depth by CC #1
This parameter is active only for CC #1 - Modulation
MIDI command. It doesn't work with instrument's MG
wheel controller!
The basic VCF modulation depth set by the VCF LFO
AMOUNT parameter (see above) can be increased by
CC #1 (Modulation) MIDI command. The parameter
adjusts maximal possible increasing of the modulation.
The parameter can be temporarily changed by MIDI CC
Nr. 27 - see chapter 5.1.2.2.
The parameter value is 0 to 127. For value 0 , the basic modulation depth isn’t affected by the CC #1. For values
from 1 to 127, the basic modulation depth is increased by the the CC #1. Maximal modulation depth (i.e. when
CC #1 with value 127 is received) is then directly proportional to the parameter value (see fig. 11).