background image

General Troubleshooting 

Applies to 

Symptom Solution(s) 

Lights 

Foggers 

& Snow 

Controllers 

Dimmers

& Chaser 

Auto shut off 

Check fan thermal switch reset 

9

Beam is very dim or not 
bright

Clean optical system or replace lamp 

Check 220/110v switch for proper setting 

9

Breaker/Fuse keeps 
blowing 

Check total load placed on device 

9

Chase is too slow 

Check users manual for speed adjustment 

9

9

9

Device has no power 

Check for power on Mains. 

Check device’s fuse. (internal and/or external) 

9

9

9

Fixture is not 
responding

Check DMX Dip switch settings for correct addressing 
Check DMX cables 
Check polarity switch settings  

9

Fixture is on but there 
is no movement to the 
audio

Make sure you have the correct audio mode on the control 
switches. If audio provided via ¼” jack, make sure a live 
audio signal exists 

Adjust sound sensitivity knob 

9

9

9

Lamps cuts off 
sporadically  

Possible bad lamp or fixture is overheating. 

Lamp may be at end of its life. 

9

Light will not come on 
after power failure 

Some discharge lamps require a cooling off period before 
the electronics in the fixture can kick start it again, wait 5 to 
10 minutes before powering up 

9

Loss of signal 

Use only DMX cables 

Install terminator 
Note: Keep DMX cables separated from power cables or 
black lights. 

9

9

9

9

Moves slow 

Check 220/110v switch for proper setting 

9

No flash 

Re-install bulb, may have shifted in shipping 

9

No laser output 

Bounce mirror motor may have shifted during shipping, 
readjust

9

No light output 

Check slip ring & brushes for contact  

Install bulb 

Call service technician 

9

Relay will not work 

Check reset switch 

Check cable connections 

9

Remote does not work 

Make sure connector is firmly connected to device 

9

9

Stand alone mode 

All Chauvet lighting fixtures featuring stand-alone functions 
do not require additional settings, simply power the fixture 
and it will automatically enter into this mode 

9

If you still have a problem after trying the above solutions, please contact CHAUVET Technical 
Support at the location on the next page. 

SX Gobo Manual 

10

2006-12-11/15:16

Summary of Contents for SX Gobo













Reviews: