DMX Operation
The HZ-1000 is a 2 channel DMX unit. Channel 1 controls the volume output and channel 2 controls the
speed of the fan which pushes the haze. To operate in DMX mode, you must link the unit to your DMX
chain using a premium quality 3-pin DMX cable in the following configuration. 'Out' from the first unit to 'In'
on the second, 'Out' from the second to 'In' on the third and so on.
The HZ-1000 is a 2 channel DMX fixture. Please consult the controller manual to determine the proper
address for the units.
Example: To set the address at 12
Installation / Mounting
The Hazer must be used in a horizontal position sitting on a level surface or it may be mounted using the
bracket provided. Ensuring that the fog is not shooting directly at anyone's face. Whatever method of instal-
lation you choose, the Hazer must not have more than a 15 degree angle of inclination. We always
suggest that for safety purposes use of a suitable hanging clamp and safety cable is essential. CHAUVET
offers a range of items, which are ideal for safe mounting.
Replacing Fuses
If the unit does not function at all when connected to the main power supply then it is highly likely that the
fuse has blown.
Disconnect from main power supply before attempting to replace the fuse.
In order to replace the fuse, disconnect from the main power supply first, and then remove the fuseholder
cover to reveal the fuse. The unit has a label attached which indicates the correct fuse rating and you will
also find this listed as part of the specifications for the unit later in this guide. It is most important that
replacement fuses are of the correct rating. Failure to use the correct fuse could damage the lighting effect
beyond economic repair.
The fuse should simply be placed inside the holder and the cover replaced. When this is done connect to
the main power supply to check. If the unit is still not working then please contact CHAUVET.
Cleaning
Cleaning your haze machine regularly will help reduce costly parts replacement and repair charges.
After every 40 hours of continuous operation or when the machine will be idle for a long time it is recom-
mended to run a cleaning solution composed of 80% distilled water and 20% white vinegar through the
system to prevent the accumulation of particles in the heating element.
1.
While unit is unplugged and cool, unscrew nozzle at very front of unit (fig.1) and clean out debris
with white vinegar and a pipe cleaner, making sure that the hole is free and unobstructed.
2.
Empty all haze/fog fluid from the machine and replace with cleaning solution in the tank. Plug unit
in
and allow to warm as usual.
3.
Run unit in a well ventilated area until tank is empty.
4.
Replace nozzle.
5.
Cleaning is now complete. Unplug and refill with a quality water based Haze/fog fluid once cool.
All haze/fog machines are prone to clogging due to the consistency of Haze/fog fluid and the high
temperatures at which it vaporizes. However a well maintained machine should provide years of reliable
use. The body of the unit may be cleaned with a dry cloth. Store dry.
Maintenance & Servicing
Work on internal parts should be carried out by a qualified technician. Removal of any covers is considered
a breach of warranty and will not be covered under any such agreement unless authorized first by Chauvet.
Introduction
Congratulations on the purchase of your new CHAUVET Ultimate HZ machine. We are confident you will
enjoy many trouble free hours with this unit. To assist with the care and use of the product we have pre-
pared this short guide.
Operation
Before connecting this unit to the mains power supply for the first time you must first fill the fluid tank with
haze/fog fluid and check that the nozzle is clean and unobstructed. Always monitor fog fluid level as run-
ning the machine with no fluid could cause permanent damage.
This Hazer/fog machine has been designed to function on a mains power supply of either 120V~60Hz or
230V~50Hz and has been fitted with a suitable power plug for use with your local voltage. Check the label
on the unit and the power plug for the correct voltage.
Place the machine on a level surface, remove the screw in the fluid access panel, lift panel and loosen the
cap of the fluid tank to fill with quality unscented water based light Haze/fog fluid. We recommend use of
CHAUVET fluid as it has been specially formulated for use with CHAUVET machines. Plug the remote
control unit into the socket at the rear and switch on to allow time to preheat.
Please do not touch or place anything in close proximity to the nozzle during operation or preheat as there
is a danger of burns.
It is normal for your Hazer to have a recycling period after long bursts when the unit will shut itself down for
a short period in order to heat up to temperature. During this time no Haze/fog can be produced. The red
light on the unit and the remote will illuminate when the unit is ready for action again.
Due to the high operating temperature of Hazer/fog machines it is advised that the effect be used in well
ventilated areas taking care not to obstruct the air vents. After use, allow time to 'cool' for safety before
moving or touching.
·
Never use any other type of liquid other than UNSCENTED water based light haze/fog fluid.
·
Use of any other fluids or additives will void the warranty.
Controlling the HZ-1000
FC-4H
S
T
imer remote - Plug the controller into the back of the HZ-1000. To engage the timer function
depress the yellow button on the handheld unit and adjust the the INTERVAL knob. The INTERVAL knob
regulates the length o time of the fog blast. The blast can be set for between 10 and 200 seconds. The
VOLUME knob controls the amount of haze/fog. This can be set between 0% and 100%. For continuous
hazing, depress the red button maked CONTINUOUS. This will set the unit to haze steadily at the selected
volume. The green MANUAL button overrides all the buttons but not the knobs to deliver a full volume blast
of Haze for as long as the button is held down.
FOR PROPER HAZE OPERATION SET VOLUME TO LOWEST SETTING
• HZ Fluid Tank Access
• Directional Flap for Output
• Haze / Fog Output Nozzle
On the Rear
• DMX Input / Output
• DIP Switches
• Socket for Remote
Control
• On/Off Switch
• Power Cord Socket and
Fuse holder
1
2
3
4
5
6
7
8
9
10
Off
On
Value
1
2
4
8
16
32
64
128
256
1.Set SW 10 to OFF.
2. Count the value of the switches in the on position.
and SW 4 equals 8.
3. Set SW 3 and SW 4 to the ON position. (4 + 8 = 12)
