background image

 

 
2                                                             4 
 
 

 

 

 
 
 
 
The out-feed end of the thicknesser bed 
has a pull-out support that can be 
extended to support the work piece as it 
emerges. 

 
 

 
General Guide 

 
When faced with a rough sawn piece of timber which requires planing on all 4 sides and taking down to a 
specific finished dimension, follow this guide: 
 

  Set the machine up for planing. 

  Identify the flattest of the two wider faces on the timber. (Face 1 on diagram) 

  Pass that side over the planer as many times as necessary until a flat and smooth finish is achieved. 

  Hold the planed side firmly against the guide fence (set at 90 degrees to the bed) and pass the 

narrow side (Face 2 on diagram) over the planer as many times as necessary until a flat and smooth 
finish is achieved. 

  You should now have two planed sides at 90 degrees to each other. 

  Set the machine up for thicknessing. 

  Pass the timber through the thicknesser with the wider, already planed side (Face 1 on diagram) 

facing down against the thicknessing bed. Continue until the desired thickness for the timber is 
reached. 

  Finally, pass the timber through the thicknesser with the planed narrow side (Face 2 on diagram) 

facing down against the thicknessing bed. Continue until the desired thickness for the timber is 
reached. 

 
 
 
 

 
 
 
 
 
 

 
 
 
 
 
 
 
 

Summary of Contents for PT250

















Reviews: