background image

 

7

20.  Check that the electric circuit is adequately protected and that it corresponds with the power, 

voltage and frequency of the motor, check that there is a ground connection, and a regulation 
differential switch upstream. 
Check on the functioning of the machine. 

21.  Never open the switch box on the motor. Should this be necessary, contact a qualified 

electrician. 

22.  Make sure that the machine and the cable never come in contact with water. 
23.  Treat the power cable with care, do not attempt to move the machine by pulling the cable, do 

not yank the cable to unplug it; keep the cable away from excessive heat, oil and sharp 
objects. 

24.  Never leave the machine unattended with the power supply “on”, also disconnect the power 

cable when not in use, when carrying out maintenance work, when changing attachment or 
moving the machine. 

25.  Before starting work, hydraulic pipes and hoses shall be inspected and the stopping devices 

shall be tested. 

26.  Keep the working area free from obstructions, e.g. logs, split wood etc. 
27.  Stop the machine before cleaning or making adjustments. 
28.  The hazards may arise from particular characteristics of wood when being split(e.g.knots, logs 

of irregular shape etc.) 

                                                                               
 

TECHNICAL SPECIFICATIONS 

 
Technical specifications 

Model 

YP3725A3/1 

Voltage 
Frequency 
Power input 
No load speed 
Insulation class 
Protection degree 
Max. splitting force (tons) 
Diameter 
Length 
Max. Hydraulic oil capacity 
Nominal mass 
Max. operating mass 
L

pa 

(sound pressure level) 

L

wa 

(sound power level) 

240V~ 
50Hz 
1500W 
2,950min

-1

 

Class B 
IP 54 

50-250mm 
370mm 

5t 

42kg 

48kg 

66.3 dB(A) 
79.3dB(A)

 

 
Electrical Safety 

 
WARNING!

 Always check that the power 

supply corresponds to the voltage on the 
rating plate. 

Summary of Contents for LS5T37A


















Reviews: