manualshive.com logo in svg

Charlton & Jenrick INFINITY 800HD BF UBL, Instruction For User, Installation & Servicing

Share
Download
Charlton & Jenrick INFINITY 800HD BF UBL Instruction For User, Installation & Servicing Download Page 12

 

 

 

12 

 LT 8381 (ISS 01) 

800 HD B.F. with UBL USERS INSTRUCTION

 

 

 Cleaning & Laying the fuel bed (users instructions) 

 

Warning:-

Before you clean any part of the appliance ensure that the appliance is switched off and cool. 

CLEANING: BLACK PAINTED SURFACES 

•

 

These surfaces should be dusted regularly and any marks removed with a soft cloth. 

•

 

Abrasive or chemical cleaner should never be used. 

CLEANING: GLASS PANEL 

From time to time it may be necessary to clean the glass panel. 

We recommend you use a Ceramic Hob Cleaner (brands such as 

HOB BRITE and VITRO CLEN have been found to be 

acceptable)

 these are available from most leading Supermarkets.  

Remove the glass panel as follows:- 

 

 

 

•

 

c

Carefully lift up and out the inner frame.

  

 

 
 
 
 
 
 
 
 
 
 
 

•

 

Remove the three fixing brackets located on the 
top and sides of the glass panel. 

•

 

Remove the 4 x nuts on each of the Glass Clamps 
leaving the top Clamp till last, remember to hold 
the Glass Panel back when removing the nuts. 

 

 

 

 

 

Summary of Contents for INFINITY 800HD BF UBL













































Reviews:

No comments

Brands by name

Popular brands

Load more brands