7
Burner Flame Check
• Remove grates and flametamers. Light burners, rotate knobs
from HI to LOW. You should see a smaller flame in LOW
position than seen on HI. Always check flame prior to each
use. Perform flame check for sideburner. If only low flame is
seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.
Turning Grill Off
• Turn all knobs to OFF position. Turn LP tank OFF by turning
hand-wheel clockwise to a full stop.
H I
LOW
Match Lighting
▲
▲
▲
▲
▲
Do not lean over grill while lighting.
1. Open lid during lighting.
2. Place lit match into match
lighting stick, then into lighting
hole on right side of grill.
3. Push in and turn far right burner
knob to HI. Be sure burner lights
and stays lit.
4. Light adjacent burners in sequence by pushing knobs in
and turning to HI.
Sideburner Ignitor Lighting
▲
▲
▲
▲
▲
Do not lean over grill while lighting.
1. To ignite side burner, open side burner cover.
2. Turn side burner knob to HI,
push and hold ELECTRONIC IGNITOR button.
3. If side burner does NOT light, turn knob to OFF,
wait 5 minutes, then repeat lighting procedure or use match.
Match Lighting
1. To match light SIDEBURNER, open
sideburner cover.
2. Place lit match near burner.
3. Push in and turn sideburner
knob counter-clockwise. Be
sure burner lights and stays lit.
• If burner does not light turn knobs to OFF, wait 5
minutes, try again.
Ignitor Check
• Turn gas off at LP tank. Push and hold electronic ignitor
button or push in and turn sideburner knob counter-
clockwise. "Clicks" should be heard and spark seen each
time between collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is OFF at LP tank before
checking valves. Knobs lock in OFF position. To check
valves, first push in knobs and release, knobs should spring
back. If knobs don't spring back, replace valve assembly
before using grill. Turn knobs to LOW position then turn back
to OFF position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use only valve/
hose/regulator specified by manufacturer.
Cleaning The Burner Assembly
Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting grill.
1. Turn gas off at control knobs and LP tank.
2. Remove cooking grates, flametamers, grease tray and grease
receptacle.
3. Remove cotter pins from beneath each burner "foot" using a
screwdriver or needle nose pliers.
4. Carefully lift each burner up and away from valve openings.
We suggest three ways to clean the burner tubes. Use the one
easiest for you.
(A) Bend a stiff wire (a light weight coat hanger works well)
into a small hook. Run the hook through each burner tube
and burner several times.
(B) Use a narrow bottle brush with a flexible handle (do not
use a brass wire brush), run the brush through each burner
tube and burner several times.
(C) Wear eye protection: Use an air hose to force air into the
burner tube and out the burner ports. Check each port to make
sure air comes out each hole.
5. Wire brush entire outer surface of burner to remove food
residue and dirt.
6. Clean any blocked ports with a stiff wire such as an open paper
clip.
7. Check burner for damage, due to normal wear and corrosion
some holes may become enlarged. If any large cracks or holes
are found replace burner.
VERY IMPORTANT: Burner tubes must reengage valve
openings.
