background image

  P/N  42804003 

• 02204809

 (12-06-07)

Tools needed for

assembly:

Adjustable Wrench

Screwdriver

04201101

02204809

Smoker, BBQ and Grill

CAUTION

Some parts may contain sharp edges. Wear 

protective gloves if necessary.

Read and follow all safety statements, warnings, 

assembly instructions and use & care directions 

before attempting to assemble and cook.

WARNING

CARBON MONOXIDE HAZARD

Burning charcoal inside can kill you.  It gives off 

carbon monoxide, which has no odor.  NEVER burn 

charcoal inside homes, vehicles or tents.

NEVER LEAVE FIRE UNATTENDED!

Do not allow small children near flame.  Hot embers 

can fly out in breezy conditions.  Adequate fire 

extinguishing material should be readily available.

WARNING

CALIFORNIA PROPOSITION 65
1.  This product is produced with or contains 

chemicals known to the State of California to 

cause cancer, birth defects, or other reproductive 

harm.

2.  This product contains chemicals, including lead 

and lead compounds, known to the State of 

California to cause cancer, birth defects or other 

reproductive harm.

     

Wash your hands after handling this product.

CAUTION

THIS UNIT IS HEAVY!

DO NOT assemble without a helper.

WARNING

All surfaces can be hot during use.  Use protection 

as required to prevent burning.

Do not use this unit on or near combustible surfaces 

or structures such as wood decks, dry leaves or 

grass, vinyl or wood siding, etc.

SEE OWNERS MANUAL FOR IMPORTANT SAFETY 

INFORMATION.

If you have questions or need assistance during assembly, please call 

.

To insure your satisfaction and for follow-up service,

 register your grill online at www.grillregistration.com

1-800-241-7548

Summary of Contents for American Gourmet 02204809













Reviews: