background image

CAUTION

If ignition does NOT occur in 5 seconds, turn the 

burner controls OFF, wait 5 minutes and repeat the 

lighting procedure. If the burner does not ignite with 

the valve open, gas will continue to flow out of the 

burner and could accidently ignite with risk of injury.

Turn controls and gas source or tank OFF when not 

in use.

WARNING

Match-Lighting

s

 Do not lean over grill while lighting.

1.

 

2. Open lid. 

Turn on gas at LP cylinder.

 

3.

Place lit match into match holder (hanging from cart side 
panel), then into lighting hole on right or left side of grill.

4.

Push in and turn far right or far left burner knob to HIGH      . 
Be sure burner lights and stays lit.

5.

Light adjacent burners in sequence by pushing knobs in and 
turning to HIGH      . 

Turn       

OFF 

all burner control valves. 

Side Burner Lighting Instructions:

s

 

 

Do not lean over grill while lighting.

1. Turn       

OFF

 all gas burner control valves.

2. Turn 

ON

 gas source or tank.

3. Open lid during lighting.
4. To ignite SIDEBURNER, turn sideburner knob to the      

position.

5. Push and hold the ELECTRONIC IGNITOR button untill the 

sideburner lights.

6. Once burner has ignited, turn knob to desired setting.
7 If ignition does not occur in 5 seconds, turn the burner control 

to       OFF, wait 5 minutes, and repeat the lighting procedure.

Sideburner Match Lighting

1. 
2. Open sideburner lid. Turn on

gas at LP cylinder.

3. Place lit match near burner.
4. Turn sideburner knob to 
    HIGH      . Be sure burner

lights and stays lit.

Turn       

OFF

 all burner control valves.

Burner Flame Check

•Remove cooking grates and troughs. Light burners, rotate 

knobs from             to     . You should see a smaller flame in

 

        position than seen on           . Perform burner flame check 

on sideburner, also. Always check flame prior to each use. If 
only low flame is seen refer to "Sudden drop or low flame" in 
the 

Troubleshooting Section

.

Turning Grill Off

•Turn all knobs to  

position. Turn LP cylinder off by 

turning hand-wheel clockwise to a full stop.

Ignitor Check

•Turn gas off at LP cylinder.

 Press and hold electronic ignitor 

button.  "Click" should be heard and spark seen each time 
between collector box or burner and electrode. See 

"Troubleshooting"

 if no click or spark.

Valve Check

•Important: Make sure gas is off at LP cylinder before 

checking valves

.  Knobs lock in  

position. To check 

valves, first push in knobs and release, knobs should spring 
back. If knobs do not spring back, replace valve assembly 
before using grill. Turn knobs to

 LOW

 position then turn back to  

position. Valves should turn smoothly.  

Hose Check

Before each use, check to see if hoses are cut or worn. 

Replace damaged hoses before using grill. Use only 
valve/hose/regulator specified by manufacturer.

General Grill Cleaning 

•Do not mistake brown or black accumulation of grease and 

smoke for paint.  Interiors of gas grills are not painted at the 
factory 

(and should never be painted)

. Apply a strong solution 

of detergent and water or use a grill cleaner with scrub brush 
on insides of grill lid and bottom. Rinse and allow to completely 
air dry. 

Do not apply a caustic grill/oven cleaner to painted 

surfaces.

 

• 

Plastic parts: 

Wash with warm soapy water and wipe dry.

 

Do not use citrisol, abrasive cleaners, degreasers or a 

concentrated grill cleaner on plastic parts. Damage to and 
failure of parts can result. 

•Porcelain surfaces: 

Because of glass-like composition, most 

residue can be wiped away with baking soda/water solution or 
specially formulated cleaner.

 

Use nonabrasive scouring powder 

for stubborn stains.

•Painted surfaces: 

Wash with mild detergent or nonabrasive 

cleaner and warm soapy water. Wipe dry with a soft 
nonabrasive cloth.

•Stainless steel surfaces: 

To maintain your grill’s high quality 

appearance, wash with mild detergent and warm soapy water 
and wipe dry with a soft cloth after each use. Baked-on grease 
deposits may require the use of an abrasive plastic cleaning 
pad. Use only in direction of brushed finish to avoid damage. 
Do not use abrasive pad on areas with graphics.

• Cooking surfaces:

 If a bristle brush is used to clean any of

the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.

OFF     

 

OFF 

 

OFF 

 

8

Summary of Contents for 466247109





























Reviews: