background image

6

• 

If you notice grease or other hot material dripping from grill 

onto valve, hose or regulator, turn off gas supply at once. 
Determine the cause, correct it, then clean and inspect valve, 
hose and regulator before continuing. Perform a leak test.

• 

Keep ventilation openings in cylinder enclosure (grill cart) free 

and clear of debris.

• 

Do not store objects or materials inside the grill cart enclosure 

that would block the flow of combustion air to the underside of 
either the control panel or the firebox bowl.

• 

The regulator may make a humming or whistling noise during 

operation. This will not affect safety or use of grill.

• 

If you have a grill problem see the 

"Troubleshooting” 

Section.

• 

If the regulator frosts, turn off grill and LP cylinder valve 

immediately. This indicates a problem with the cylinder and it 
should not be used on any product. Return to supplier!

Leak Testing Valves, Hose and Regulator

1.Turn all grill control knobs to OFF.

2.

Be sure regulator is tightly connected to LP cylinder.

3.

Completely open LP cylinder valve by turning hand wheel 

counterclockwise. If you hear a 

rushing sound

, turn gas off 

immediately. There is a major leak at the connection. 

Correct 

before proceeding

.

4.

Brush soapy solution onto areas circled below, or other similar 

fittings on your grill.

5.If “growing”

 bubbles appear, there is a leak. Close LP cylinder 

valve immediately and retighten connections. 

If leaks cannot be 

stopped do not try to repair. 

Call for replacement parts. 

6.

Always close LP cylinder valve after performing leak test by 

turning hand wheel clockwise.

NOTE: Sideburner shelf 

fascia and other parts not 

shown for clarity.

• Outdoor gas appliance is not intended to be installed in or 

on a boat.

• Outdoor gas appliance is not intended to be installed in or on 

an RV.

• Never attempt to attach this grill to the self-contained LP 

gas system of a camper trailer or motor home.

NOTE: Your grill may NOT 

be equipped with a 

sideburner. 

WARNING

Safety Tips

• 

Before opening LP cylinder valve, check the coupling nut for 

tightness.

• 

When grill is not in use, turn off all control knobs and LP 

cylinder valve. 

• 

Never move grill while in operation or still hot.

• 

Some surfaces will be hot during use.  Use long-handled 

barbecue utensils and oven mitts to avoid burns and splatters.

• 

Maximum load for sideburner and side shelf is 10 lbs.

• 

The grease tray or cup  

must 

be installed during use and  

emptied after each use. Do not remove grease tray or cup 
until grill has completely cooled.

• 

Clean grill often, preferably after each cookout. If a bristle 

brush is used to clean any of the grill cooking surfaces, ensure 
no loose bristles remain on cooking surfaces prior to grilling. It 
is not recommended to clean cooking surfaces while grill is hot. 

• Do not use grill until leak-tested.

• If a leak is detected at any time, STOP!  Turn off 

gas at source and correct leak.

• If you cannot stop a gas leak by closing the LP cylinder valve 

leave area and call your fire department!

WARNING

Summary of Contents for 463367016

































Reviews: