background image

Troubleshooting - Electronic Ignition

Problem (Ignition)

SECTION I

No sparks appear at 
any electrodes when 
Electronic Ignition Button

is pressed; 

no noise

 can

 be heard from spark 

module.

SECTION II

SECTION III

Sparks are present 
but not at all 
electrodes and/or not 
at full strength

Possible Cause

• Battery not installed 

properly.

• Dead battery.

• Button assembly not 

installed properly.

• Faulty spark module.

• Output lead 

connections not 
connected.

• Output lead 

connections not 
connected.

• Arcing to grill away 

from burner(s).

• Weak battery.

• Electrodes are wet.

• Electrodes cracked or 

broken “sparks at 
crack”.

Check Procedure

• Check battery orientation.

• Has battery been used 

previously?

• Check to insure threads are 

properly engaged. Button 
should travel up and down 
without binding.

• If no sparks are generated 

with new battery and good 
wire connections, module is 
faulty.

• Are output connections on 

and tight?

• Are output connections on 

and tight?

• If possible, observe grill in 

dark location. Operate 
ignition system and look for 
arcing between output wires 
and grill frame.

• All sparks present but weak 

or at slow rate.

• Has moisture accumulated 

on electrode and/or in burner 
ports?

• Inspect electrodes for 

cracks.

Prevention/Solution

• Install battery (make sure that “+” and “–” 

connectors are oriented correctly, with “+” end up 
and “–” end down.)

• Replace battery with new AA-size alkaline battery.

• Unscrew button cap assembly and reinstall, making 

sure threads are aligned and engaged fully.

• Replace spark module assembly.

• Remove and reconnect all output connections at 

module and electrodes.

• Remove and reconnect all output connections at 

module and electrodes.

• If sparks are observed other than from burner(s), 

wire insulation may be damaged. Replace wires.

• Replace battery with a new AA-size alkaline battery.

• Use paper towel to remove moisture.

• Replace cracked or broken electrodes.

No sparks appear at 
any electrodes when 
Electronic Ignition Button

is pressed; noise 

can

 be heard from spark 

module.

22

    

Summary of Contents for 463262911

























Reviews: