Char-Broil 463241414 Product Manual Download Page 4

4

WARNING

For Safe Use of Your Grill and to Avoid 
Serious Injury:

•  

Do not let children operate or play near grill. 

• 

 Keep grill area clear and free from materials that burn.

 

• 

 Do not block holes in sides or back of grill. 

 

• 

 Check burner flames regularly.

•  

Do not use charcoal or ceramic briquets in a gas grill. 

• 

 Use grill only in well-ventilated space. NEVER use in 

enclosed space such as carport, garage, porch, 
covered patio, or under an overhead structure of any 
kind.

 

•  

Do not cover grates with aluminum foil or any other 
material.  This will block burner ventilation and 
create a potentially dangerous condition resulting 
in  property damage and/or personal injury.

•  Use grill at least 3 ft. from any wall or surface. 

Maintain 10 ft. clearance to objects that can catch 
fire or sources of ignition such as pilot lights on water 
heaters, live electrical appliances, etc.

•  Apartment Dwellers:

Check with management to learn the requirements 
and fire codes for using an LP gas grill in your 
apartment complex. If allowed, use outside on the 
ground floor with a three (3) foot clearance from 
walls or rails. Do not use on or under balconies.

•  NEVER attempt to light burner with lid 

closed. A buildup of non-ignited gas 
inside a closed grill is hazardous.

•  Never operate grill with LP cylinder out of 

correct position specified in assembly 
instructions. 

•  Always close LP cylinder valve and remove 

coupling nut before moving LP cylinder from 
specified operation position.

• 

If you notice grease or other hot material dripping from 

grill onto valve, hose or regulator, turn off gas supply 
at once. Determine the cause, correct it, then clean 
and inspect valve, hose and regulator before 
continuing. Perform a leak test.

• 

Keep ventilation openings in cylinder enclosure (grill 

cart) free and clear of debris.

• 

Do not store objects or materials inside the grill cart 

enclosure that would block the flow of combustion air 
to the underside of either the control panel or the 
firebox bowl.

• 

The regulator may make a humming or whistling noise 

during operation. This will not affect safety or use of 
grill.

• 

If you have a grill problem see the 

"Troubleshooting” 

Section.

• 

If the regulator frosts, turn off grill and LP cylinder 

valve immediately. This indicates a problem with the 
cylinder and it should not be used on any product. 
Return to supplier!

Match-Lighting

 Do not lean over grill while lighting.

5. 

Push in and turn burner knob to the 

     HIGH

 position.  

Be sure burner lights and stays lit.

6. 

Light adjacent burners in sequence by pushing knobs in 
and turning to the      

HIGH

 position.

If ignition does NOT occur in 5 seconds, turn the 
burner controls      OFF, wait 5 minutes and repeat 
the lighting procedure. If the burner does not ignite 
with the valve open, gas will continue to flow out of 
the burner and could accidently ignite with risk of 
injury.

Turn controls and gas source or tank OFF 
when not in use.

4.

 Place match into match holder (hanging from side panel 

of grill). Light match; then light burner by placing match 
through the match light hole on side of grill.

8.

 

For grills equipped with ELECTRONIC IGNITION at 
each burner:

Repeat steps 4 through 6 to light each burner.

9.

 Once each burner has ignited, turn knobs to desired 

setting.

Ignitor Lighting

 

 Do not lean over grill while lighting.

1. 

Turn 

      OFF

 gas burner control valves. 

2. 

Turn 

ON

 gas at LP cylinder.

3. Open lid during lighting.

4. 

To ignite, push and turn 

IGNITION BURNER

 knob to 

 

         HIGH

5. 

Immediately, push and hold 

ELECTRONIC IGNITION

 

button until the burner lights.

6. 

If ignition does NOT occur in 5 seconds, turn the burner 
controls 

     OFF

, wait 5 minutes and repeat the lighting 

procedure.  If ignitor does not work, follow match lighting 
instructions. 

7.

 To ignite remaining burners, turn knob to the 

     HIGH

 

position starting with the burners closest to IGNITION 
BURNER first.  

CAUTION

WARNING

3 ft.

3 ft.

1. 

Turn 

      OFF

 gas burner control valves. 

2. 

Turn 

ON

 gas at LP cylinder.

3. Open lid during lighting.

Leak Testing Valves, Hose and Regulator

1.Turn all grill control knobs to OFF.
2.

Be sure regulator is tightly connected to LP cylinder.

3.

Completely open LP cylinder valve by turning hand 

wheel counterclockwise. If you hear a 

rushing sound

turn gas off immediately. There is a major leak at the 
connection. 

Correct before proceeding

.

4.

Brush soapy solution onto areas circled below, or other 

similar fittings on your grill.

5.If “growing”

 bubbles appear, there is a leak. Close 

LP cylinder valve immediately and retighten 
connections. 

If leaks cannot be stopped do not try 

to repair. 

Call for replacement parts. 

6.

Always close LP cylinder valve after performing leak 

test by turning hand wheel clockwise.

NOTE: Sideburner 
shelf fascia and other 
parts not shown for 
clarity.

• Outdoor gas appliance is not intended to be installed 

in or on a boat.

• Outdoor gas appliance is not intended to be installed 

in or on an RV.

• Never attempt to attach this grill to the self-contained 

LP gas system of a camper trailer or motor home.

NOTE: Your grill 
may NOT be 
equipped with a 
sideburner. 

WARNING

Safety Tips

• 

Before opening LP cylinder valve, check the coupling 

nut for tightness.

• 

When grill is not in use, turn off all control knobs and LP 

cylinder valve. 

• 

Never move grill while in operation or still hot.

• 

Some surfaces will be hot during use.  Use long-

handled barbecue utensils and oven mitts to avoid 
burns and splatters.

• 

Maximum load for sideburner and side shelf is 10 lbs.

• 

The grease tray or cup  

must 

be installed during use 

and  emptied after each use. Do not remove grease tray 
or cup until grill has completely cooled.

• 

Clean grill often, preferably after each cookout. If a 

bristle brush is used to clean any of the grill cooking 
surfaces, ensure no loose bristles remain on cooking 
surfaces prior to grilling. It is not recommended to clean 
cooking surfaces while grill is hot. 

• Do not use grill until leak-tested.
• If a leak is detected at any time, STOP!  

• If you cannot stop a gas leak by closing the LP cylinder 

valve leave area and call your fire department!

WARNING

Summary of Contents for 463241414





































Reviews: