background image

12

.

Gas odor with extreme yellow tipping of flame.

.

Heater does NOT reach the desired temperature.

.

Heater glow is excessively uneven.

.

Heater makes popping noises.

.

Spiders and insects can nest in burner or orifices.

This dangerous condition can damage heater and

render it unsafe for use. Clean burner holes by using

a heavy-duty pipe cleaner. Compressed air may help

clear away smaller particles.

.

Carbon deposits may create a fire hazard. Clean

dome and burner screen with warm soapy water if

any carbon deposits develop.

Note: In a salt-air environment (such as near an ocean),

corrosion occurs more quickly than normal. Frequently

check for corroded areas and repair them promptly.

TIP:

Use high-quality automobile wax to help maintain the

appearance of your heater. Apply to exterior surfaces from

the pole down. Do not apply to emitter screen or domes.

Storage

Between uses:

.

Turn Control Knob OFF.

.

Disconnect LP source.

.

Store heater upright in an area sheltered from direct

contact with inclement weather (such as rain, sleet,

hail, snow, dust and debris).

.

If desired, cover heater to protect exterior surfaces

and to help prevent build up in air passages.

Note: Wait until heater is cool before covering.

During periods of extended inactivity or when

transporting:

.

Turn Control Knob OFF.

.

Disconnect LP source and move to a secure,

well-ventilated location outdoors.

.

Store heater upright in an area sheltered from direct

contact with inclement weather (such as rain, sleet,

hail, snow, dust and debris).

.

If desired, cover heater to protect exterior surfaces

and to help prevent build up in air passages.

.

Never leave LP cylinder exposed to direct sunlight or

excessive heat.

Note: Wait until heater is cool before covering.

Service

Warranty

Repair to gas passages and associated components

should be done only by a qualified service person.

Caution:

Always

allow

heater

to

cool

before

attempting service.

Manufactured by:

Changzhou Gardensun Furnace Co., Ltd.
No. 1, Boyi Town, Changzhou City,
Jiangsu Province P.R. China

1 YEAR LIMITED WARRANTY - CUSTOMERS IN CANADA

IMPORTANT

Only return this product to the store if it was purchased within 90 
days. If you have problems af ter 90 days of purchase, please 
email our customer service department for any questions or 
concerns: www.patioheaterpartsonline.com OR PLEASE 
CALL 888-775-1330 DATED PROOF OF PURCHASE 
REQUIRED FOR WARRANTY SERVICE.

WARRANTY

This product is inspected, tested and carefully packaged to 
minimize the chance of damage during shipment. If a part 
(excluding light bulbs and fuses*) within one year from the date of 
purchase proves to be defective in material or fabrication under 
normal use, the part will be repaired or replaced. The Company's 
obligation under the warranty is to replace or repair defective parts 
at our discretion. Any expenses or damage resulting from the 
installation, removal or transportation of the product will the 
responsibility of the owner and are not covered by this warranty.
The owner assumes all other risks arising out from the use or 
misuse of the product. The warranty will be void if the product 
damage or failure is deemed by the Company to be caused by 
accident, alteration, misuse, abuse, incorrect installation or 
removal, or connection to an incorrect power source by the owner.
The Company neither assumes, nor authorizes any person or 
entity to assume for it any obligation or liability associated with its 
products. * Light bulbs and fuses are not covered under this 
warranty. If you have any questions regarding the warranty or 
service, please call our toll free number: 888-775-1330

Distributed by:
AZ Patio Heaters
8550 N 91st Ave Ste C-25
Peoria, AZ 85345

Summary of Contents for HLS01-CGT














Reviews: