background image

Getting Started

 

Using the Remote Control                                                                                                       

 

When using the remote control, aim it at remote sensor on the television. If there is an 
object between the remote control and the remote sensor on the unit, the unit may no 
operate. 

• Point the remote control at the REMOTE SENSOR located on the television.   
• When using this television in a very brightly lit area, the infrared REMOTE CONTROL 

SENSOR may not work properly. 

• The recommended effective distance for using the remote control is about 7 metres. 

Installing Batteries in the Remote Control                                       

 

1. Open the cover at the back of the remote control. 

2. Install two AAA size batteries. Make sure to match 

the “+” and “-” ends of the batteries with the 
diagram inside the compartment. 

3. Replace the cover. 

Battery Replacement                                                        

 

You will need to install the batteries into the remote control to make it operate following 
the instruction below. 
When the batteries become weak, the operating distance of the remote control will be 
greatly reduced and you will need to replace the batteries. 

Notes on Using Batteries:  
The use of the wrong type of batteries may cause chemical leakage and/or explosion. 
Please note the following: 

• Always ensure that the batteries are inserted with the + and - terminals in the correct 

direction as shown in the battery compartment. 

• Different types of batteries have different characteristics. Do not mix different types. 
• Do not mix old and new batteries. Mixing old and new batteries will shorten battery life 

and/or cause chemical leakage. 

• Replace batteries as soon as they do not work. 
• Chemicals which leak from batteries may cause skin irritation. If any chemical matter 

seeps out of the batteries, wipe it up immediately with a dry cloth. 

• The batteries may have a shorter life expectancy due to storage conditions. Remove the 

batteries whenever you anticipate that the remote control will not be used for an 
extended period.

 

 

• The batteries (battery pack or batteries installed) shall not be exposed to excessive heat 

such as sunshine, fire or the like. 

CAUTION: 
• It may result in an explosion if batteries are replaced incorrectly. 
• Only replace batteries with the same or equivalent type.

 

6

Summary of Contents for LED40YC1700UA

























Reviews: