3
Make sure the work area is clear of all unnecessary equipment and
personnel before moving a load. Personnel and equipment should be
moved clear of the area in case the load falls.
The handwheel, located on the side of the hoist, may be used to quickly take
up the slack strap prior to lifting the load. Move the "SHIFT LEVER" to the
"UP" position and rotate the wheel.
Lift the load by moving the handle in full, even strokes. Do not slam or jerk
the handle. If excessive force (more than 150 lbs.) is required to operate the
handle, the hoist is probably overloaded. Check the load and/or rigging before
proceeding. If the load is greater than the rating of the hoist, DO NOT LIFT
THE LOAD.
Never overload the hoist. Never use a cheater or extend the handle.
Once the load is lifted into position, the "SHIFT KEY" must be in the "UP"
position for holding the load. This will help prevent accidental lowering of
the load.
LOWERING A LOAD
Never let the hoist self-ratchet or the handle fly loose. The quickly moving
handle can cause injury, and self-ratcheting may damage the hoist.
Holding onto the handle, set the "SHIFT KEY" to the "DOWN" position.
Operate the handle until the "WORKING DOG" engages the ratchet wheel
tooth. Additional pressure on the handle in the same direction will release
the "HOLDING DOG". While maintaining control, slowly move the handle in
the opposite direction; lowering the load until the "HOLDING DOG" engages
the ratchet wheel. The "WORKING DOG" will then release, allowing the
operator to repeat this movement to lower the load.
When the load is completely off the hoist, the "RELEASE LEVER" may be
operated to extend the strap for unhooking.
Never operate the "RELEASE LEVER" while the hoist is loaded.
LIFTING LOADS
Maximum load rating - 2 Ton (4000 lbs./1800 kg)
!
WARNING
!
WARNING
!
CAUTION
!
WARNING
!
WARNING
REPAIR PARTS LIST FOR CHANCE TWO
TON NYLON RATCHET HOIST
4
When placing the hoist in operating position care must be taken to make sure that
the load hook and the housing hook of the hoist are on the same centerline. If the
hoist is restricted from adjusting itself to form a straight line with the direction of
loading damage to the hoist could occur.
The equipment covered in this instruction guide must be installed, used, and
serviced only by competent personnel familiar with and following good work
and safety practices. This equipment is for use by such personnel and is not
intended as a substitute for adequate training and experience in safe procedures
for this type of equipment.
The information contained in this instruction guide has been compiled as a result
of review of the product, its intended application and use considerations.
However, this instruction guide does not cover all details or situations in equip-
ment use nor does it provide for every possible contingency to be encountered
in relation to installation, operation or maintenance. Should additional informa-
tion and details be desired or specific situations arise which are not covered
adequately for the user's purpose, consult your supervisor and the appropriate
rules for safe work practices.
Nylon Web Assembly
E309-0262
Spool
P309-0260
Split Rings
P309-0539
Loop Pin
P309-0528
Screw, (Web Anchor)
P001-0177
Web Clamp for Spool
P309-0062
Yoke Spool
P309-0531
Tension Pin
P309-0272
Hoist Hand Wheel
P309-0523
Snap Rings
Up & Down Lever (Shift Key Lever) P309-0444 +
Spring Washer
Reversing Rod (Shift Key)
P309-0445
Pin
Screw
Body Dog Assembly
E309-0354 +
Main Shaft Pin
P309-0066
Main Shaft Assembly
P309-0259
Unloader Plate Subassembly
E309-0356 +
Spring
Spring
P309-0352 +
Wear Strip
P309-0818 +
Handle
E309-0264
Lower Hook Assembly
E309-0855
+ C309-0349 Repair Kit includes all items .
* Included in housing subassembly.
HANDLE BODY
SUBASSEMBLY
E309-0263
Handle Body
P309-0054
Oilite Bearing
058614
Release Key
P309-0346 +
Pin
Spring
Handle Dog Subassembly
E309-0354 +
Washer
Screw
Stop Bolt
Spring
P309-0307 +
Jam Nut
Handle Bolt
P001-0178
HOUSING
SUBASSEMBLY W/ HOOK
E309-0258
* Oilite Bearing
058613
* Oilite Bearing
019305
REMAINING PARTS
Pin
056016
Belt Guide
P309-0271
Belt Idler
P309-0057
Strap Loop Pin
P309-0270
Pin
P309-0347 +
Idler Pin
P309-0266
!
WARNING
!
CAUTION