background image

REV 91050-20140620  

6

91050

 

ENGLISH

SAFETy RULES

Maintenance and Storage

1.  Always shut off the power source and disconnect 

the spark plug wire and ground the engine, while 
repairing or adjusting the unit.

2.  Clean debris, shrubbery and chaff from the 

engine cylinder, cylinder head fins, blower house 
rotation screen, and muffler areas. If the engine is 
equipped with a spark arrestor muffler, clean and 
inspect it regularly (follow manufacturer’s service 
instructions). Replace, if damaged.

3.  Never store the unit with fuel in the tank. Fumes 

might reach an open flame spark. Allow the engine 
to cool before storing in any enclosure.

4.  Clear debris from moveable parts, but only when the 

engine is off, the fuel valve is in the “OFF” position, 
and the spark plug wire is disconnected.

5.  Check to be sure all nuts and bolts are tight to 

assure the equipment is in safe working condition.

Operation

1.  Before starting this chipper-shredder, review all 

safety rules. Failure to follow these rules may result 
in serious injury to the operator or bystanders.

2.  Be sure to confirm all connections are tight before 

each use. It is possible for connections to vibrate 
loose over time.

3.  Never leave the machine unattended with the power 

source operating.

4.  Never operate the machine when under the 

influence of alcohol, drugs or medication.

5.  The machine owner should instruct all operators in 

safe chipper-shredder operation.

6.  Always operate the chipper-shredder with all 

safety equipment in place and all controls properly 
adjusted for safe operation.

7.  Always operate the chipper-shredder at 

manufacturer’s recommended speed.

8.  Always keep hands and feet clear of moving parts.
9.  When loading the chipper-shredder, never place 

your hands inside or on the sides of the chutes, 
chambers, or intake. Never place your hands or any 
part of your body between the material and any part 
of the chipper-shredder.
a.  Never attempt to chip more than one (1) branch 

at a time, this may cause the chute, chamber or 
intake to become clogged.

b.  Never attempt to use your hand, foot or any body 

part to unclog the chipper-shredder.

c.  Only attempt to unclog with a small diameter 

stick that can get chipped.

d.  If a major clog occurs; turn the fuel valve off and 

let the unit run until dry, turn off the engine, let 
the unit cool down, unplug the spark plug wire 
and take apart the unit to see where the clog has 
occurred. Remove clog before further operation.

10. Only chip branches 3 in. (7.6 cm) or less in 

diameter.

11. Only shred dry or slightly damp material. Never 

attempt to shred material that is wet, as this may 
cause clogging to occur.

12. Use only your hand to operate the chipper-shredder 

controls.

13. Do not refuel the engine until it has cooled for several 

minutes.

Summary of Contents for 91050



































Reviews: