background image

REV 75536i-20130729  

14

75536i

 

ENGLISH

Air Filter

1.  Remove the maintenance cover.
2.  Locate the air filter plastic cover. 
3.  Unsnap the locking hinge on the cover.
4.  Remove the old filter. 
5.  Place the new filter in the assembly.
6.  Re-snap the hinge on the air filter cover.
7.  Reinstall the maintenance cover and tighten the 

cover screw securely.

Use a damp cloth to clean exterior surfaces of the engine.
Use a soft bristle brush to remove dirt and oil.
Use an air compressor (25 PSI) to clear dirt and debris 
from the engine.

Cleaning

DO NOT spray engine with water.

CAUTION

Water can contaminate the fuel system.

MAINTENANCE AND STORAGE

Adjustments

The air-fuel mixture is not adjustable. Tampering with 
the governor can damage your generator and your 
electrical devices and will void your warranty. CPE 
recommends that you contact our service line at
1-877-338-0999 for all other service and/or adjustment 
needs.

Maintenance Schedule

Follow the service intervals indicated in the following 
maintenance schedule. 
Service your generator more frequently when operating 
in adverse conditions. 
Contact our help line at 

1-877-338-0999 to locate the 

nearest Champion Power Equipment certified service 
dealer for your generator or engine maintenance needs.

Spark Arrester

1.  Allow the engine to cool completely before servicing 

the spark arrester.

2.  Remove the two screws holding the cover plate 

which retains the end of the spark arrester to the 
muffler.

3.  Remove the spark arrester screen.
4.  Carefully remove the carbon deposits from the spark 

arrester screen with a wire brush.

5.  Replace the spark arrester if it is damaged.
6.  Position the spark arrester in the muffler and attach 

with the two screws.

Failure to clean the spark arrester will result in 

degraded engine performance.

CAUTION

*To be performed by knowledgeable, experienced owners or 
Champion Power Equipment certified dealers.

Every 8 hours or daily

Check oil level

Clean around air intake and muffler

First 5 hours

Change oil

Every 50 hours or every season

Clean air filter

Change oil if operating under heavy load or in hot 

environments

Every 100 hours or every season

Change oil

Clean/Adjust spark plug

Check/Adjust valve clearance*

Clean spark arrester

Clean fuel tank and filter*

Every 250 hours

Clean combustion chamber*

Every 3 years

Replace fuel line

Summary of Contents for 75536i






























Reviews: