background image

100269 - 3400W PORTAbLE INvERTER GENERATOR

INTRODUCTION

4

SAfETY DEfINITIONS

The purpose of safety symbols is to attract your attention to 
possible dangers. The safety symbols, and their explanations, 
deserve your careful attention and understanding. The safety 
warnings do not by themselves eliminate any danger. The 
instructions or warnings they give are not substitutes for proper 
accident prevention measures.

 

DANGER

DANGER indicates a hazardous situation which, if not avoided, 
will result in death or serious injury.

 

WARNING

WARNING indicates a hazardous situation which, if not 
avoided, could result in death or serious injury.

 

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, 
could result in minor or moderate injury.

 

NOTICE

NOTICE indicates information considered important, but not 
hazard-related (e.g., messages relating to property damage).

INTRODUCTION

Congratulations on your purchase of a Champion Power Equipment 
(CPE) product. CPE designs, builds, and supports all of our 
products to strict specifications and guidelines. With proper 
product knowledge, safe use, and regular maintenance, this 
product should bring years of satisfying service.

Every effort has been made to ensure the accuracy and 
completeness of the information in this manual at the time of 
publication, and we reserve the right to change, alter and/or 
improve the product and this document at any time without prior 
notice. 

CPE highly values how our products are designed, manufactured, 
operated, and serviced as well as providing safety to the operator 
and those around the generator. Therefore, it is IMPORTANT to 
review this product manual and other product materials thoroughly 
and be fully aware and knowledgeable of the assembly, operation, 
dangers and maintenance of the product before use. Fully 
familiarize yourself, and make sure others who plan on operating 
the product fully familiarize themselves too, with the proper safety 
and operation procedures before each use. Please always exercise 
common sense and always err on the side of caution when 
operating the product to ensure no accident, property damage, 
or injury occurs. We want you to continue to use and be satisfied 
with your CPE product for years to come.

When contacting CPE about parts and/or service, you will need to 
supply the complete model and serial numbers of your product. 
Transcribe the information found on your product’s nameplate 
label to the table below

CPE TECHNICAL SUPPORT TEAM

1-877-338-0999

MODEL NUMBER

100269

SERIAL NUMBER

DATE OF PURCHASE

PURCHASE LOCATION

Summary of Contents for 100269



































Reviews: