background image

 

1

 
 

C50079 5,000lb Winch  

Owners Manual 

 

INTRODUCTION

 

 
 

Congratulations on your purchase of a Champion Power Equipment winch.  CPE 

designs and builds winches to strict specifications and with proper use and 

maintenance should bring you years of satisfying service.  

 

READ, STUDY, AND FOLLOW ALL INSTRUCTIONS BEFORE 

OPERATING THIS DEVICE. 

 

Your winch can develop tremendous pulling forces and if used unsafely or 

improperly could result in property damage, serious injury, or death.  Throughout 

this manual you will find the following symbols for caution, warning, and danger.  

Pay particular attention to the notes preceded by these symbols as they are written 

for your safety.  Ultimately, safe operation of this device rests with you, the 

operator. 

 

Indicates a potentially hazardous situation which, if not avoided, may 
result in minor or moderate injury.  This notation is also used to alert 
against unsafe practices. 

 
Indicates a potentially hazardous situation which, if not avoided, could 
result in death or serious injury. 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

CAUTION

 

 

WARNING

 

 

WARNING

 

Summary of Contents for C50079
























Reviews: