Champion Power Equipment 76520 Owner'S Manual & Operating Instructions Download Page 14

11

  

REV 76520-20120824

ENGLISH

 

76520

OPERATION

low Pressure Wash

Detergent Use

The use of detergents can dramatically reduce cleaning 
time and assist in the removal of difficult stains . Many 
detergents are customized for pressure washer use on
specific cleaning tasks . Pressure washer detergents are 
as thick as water . Using thicker detergents – like dish 
soap – will clog the chemical injection system .

System flush

After using detergents, flush the suction system by 
placing the detergent suction tube into a bucket of clean 
water .

You can effectively clean surfaces by combining the 
chemical action of detergents with high pressure rinses . 
On vertical surfaces, apply the detergent starting at the
bottom and work your way upward . This method prevents 
the detergent from sliding down and causing streaks . 
Begin high pressure rinsing at the bottom and work
your way upward . On particularly tough stains, use a 
brush in combination with detergents and high pressure 
rinsing .

1 .  Fill the detergent tank with cleaning solution .
2 .  Install the Quick Connect detergent nozzle (black) in 

the wand .

3 .  Be sure water supply is on . Start the engine . Pull the 

gun trigger to spray the detergent solution .

NEVER turn the water supply off before turning the 
engine off .

WARNING

NEVER use Bleach in the Detergent Tank . It will 
damage the pump and void the warranty .

WARNING

Use only detergents specially formulated for
pressure washers .

NOTE

The gun will only draw detergent from the tank when 
the Black Detergent Nozzle is installed in the wand .

NOTE

When spraying detergent, the detergent will be 
diluted 1:12 . Approximately 21oz . of detergent will be 
consumed from the tank for every minute sprayed .

NOTE

Your unit is equipped with a quick connect nozzle port . 
Choose the appropriate nozzle tip for the job you are 
performing .

A wide fan pattern distributes the impact of the water 
over a larger area resulting in excellent cleaning action 
with reduced risk of surface damage . Clean large surface  
areas quickly using a wide fan pattern .

High Pressure Wash

The narrow high impact spray can damage some 
surfaces .

CAUTION

Always engage the trigger safety latch when the unit 
is not in use .

CAUTION

The trigger safety latch prevents the gun from being 
triggered accidentally . Push the latch fully down to 
engage it .

Detergent Use Cont’d.

Summary of Contents for 76520






























Reviews: