background image

200911 - 3550W PORTAbLE GENERATOR

IMPORTANT SAfETY INSTRUCTIONS

6

fuel Safety

 

DANGER

GASOLINE AND GASOLINE VAPORS ARE HIGHLY 
FLAMMABLE AND EXPLOSIVE.

Fire or explosion can cause severe burns or death.

Gasoline and gasoline vapors:

 

Gasoline is highly flammable and explosive.

 

Gasoline can cause a fire or explosion if ignited.

 

Gasoline is a liquid fuel but it’s vapors can ignite.

 

Gasoline is a skin irritant and needs to be cleaned up 
immediately if spilled on skin or clothes.

 

Gasoline has a distinctive odor, this will help detect potential 
leaks quickly.

 

Gasoline expands or contracts with ambient temperatures. 
Never fill the gasoline tank to full capacity, as gasoline needs 
room to expand when temperatures rise.

 

In the case of any petroleum gasoline fire, flames should never 
be extinguished unless the fuel supply valve can be turned 
OFF. By not doing so, if a fire is extinguished and the supply 
of fuel is not turned OFF, an explosion hazard could be created.

When adding or removing gasoline:

DO NOT light or smoke cigarettes.

Always turn the generator off and let cool for a minimum of two 
minutes before removing the gasoline cap. Afterwards, loosen 
gasoline cap to relieve pressure from the gasoline tank.

Only fill or drain gasoline outdoors in a well-ventilated area.

DO NOT pump gasoline directly into the generator at the gas 
station. Always use an approved fuel container to transfer the 
gasoline to the generator.

DO NOT overfill the gasoline tank.

Always keep gasoline away from sparks, open flames, pilot lights, 
heat and other sources of ignition.

When starting the generator:

DO NOT attempt to start a damaged generator. 

Always make certain that the gasoline cap, air filter, spark plug, 
fuel lines and exhaust system are properly secured, connected 
and in place.

Always allow spilled gasoline to evaporate fully before attempting 
to start the engine.

Make certain that the generator is resting firmly on level ground.

When operating the generator:

DO NOT move or tip the generator during operation.

DO NOT tip the generator or allow fuel or oil to spill.

When transporting or servicing the generator:

Make certain that the fuel valve is in the OFF position and the 
gasoline tank is empty.

Disconnect the spark plug wire.

When storing the generator:

Store away from sparks, open flames, pilot lights, heat and other 
sources of ignition.

Do not store generator or gasoline near furnaces, water heaters, 
or any other appliances that produce heat or have automatic 
ignitions.

 

WARNING

Never use a gasoline container, gasoline tank, or any other fuel 
item that is broken, cut, torn or damaged.

Summary of Contents for 200911







































Reviews: