background image

100680 - 27 iN. 2-STAgE SNOwbLOwER

iMPORTANT SAfETY iNSTRUCTiONS

7

Top

Back

Safety Labels

These labels warn you of potential hazards that can cause serious injury. Read them carefully.

If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement.

LaBEL

DESCRIPTION

a

14

12

-L

-SF-B

DO NOT TOUCH!

 Exhaust gases, muffler and engine 

components are extremely HOT and cause burns.

 WARNING

¡NO TOCAR!

 Los gases de escape, el 

silenciador y los compnonentes del 

motor están extremadamente CALIENTES y causan quemaduras.

 ADVERTENCIA

NE TOUCHEZ PAS!

 Les gaz 

d’échappement, le silencieux et les pièces 

du moteur sont extrêmement CHAUDS et peuvent causer des brûlures.

 AVERTISSEMENT

ESSENCE SANS PLOMB SEULEMENT.

Indice d’octane minimal de 87.

Maximum 10 % d'éthanol.

GASOLINA REGULAR SOLAMENTE.

87 octanos como mínimo.

Máximo de etanol de 10%.

UNLEADED FUEL ONLY.

Minimum octane rating of 87.

Maximum 10% ethanol.

K

152

485

109

---

Colors

LPN

1412-L-SF

Rev

B

Size

145 x 53 mm

Artwork Notes

2mm safe margin; white to be printed shown in 50% 

process magenta

Revision Changes

rev b - changed to “87” octane.

This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for 
outside parties without the explicit consent of Champion Power Equipment.

Hot Surface/Fuel

B

1091-L-SF-A

 DANGER

 PELIGRO

 DANGER

K

485

2945

109

---

Colors

LPN

1091-L-SF-A

Date 5/17/17

Size

100 x 103 mm

Artwork Notes

3mm corner radius; 2mm safe margin; white to be 

printed shown in 50% process magenta

Revision Changes

---

This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for 
outside parties without the explicit consent of Champion Power Equipment.

Safety Icons

C

MANUFACTURE DATE

DATE DE FABRICATION

SERIAL NO.

N° DE SÉRIE

MODEL

MODÉLE

22

44

-L

-P

R-A

CHAMPION POWER EQUIPMENT, INC.

12039 SMITH AVENUE

SANTA FE SPRINGS, CA 90670

USA / É.-U.

1-877-338-0999

WWW.CHAMPIONPOWEREQUIPMENT.COM

MADE IN CHINA / FABRIQUÉ EN CHINE

100680

XXXXXXXXXXXX

XXXX

K

---

---

---

---

Colors

LPN

2244-L-PR

Rev

A

Size

139 x 22 mm

Artwork Notes

3mm corner radius; 2mm safe margin; to be printed 

on security substrate

Revision Changes

---

This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for 
outside parties without the explicit consent of Champion Power Equipment.

Dataplate

A

b

C

Summary of Contents for 100680







































Reviews: