background image

100330-1 - 37 TON FULL BEAM LOg SPLiTTER

iMPORTANT SAFETY iNSTRUCTiONS

10

SYmBOL

mEaNING

Always keep feet away from the wedge and the ram. Moving parts can crush or cut.

hot Surface.

 To reduce the risk of injury or damage, avoid contact with any hot surface

Open Flame alert.

 Fuel and its vapors are extremely flammable and explosive. Keep fuel away 

from smoking, open flames, sparks, pilot lights, heat, and other ignition sources.

Hold logs on sides when loading. Keep hands and feet away from cylinder, wedge, 
and partially split logs.

Never place hands or any part of the body between a log and any part of the log splitter. 
Do not split logs against the grain. Split logs end to end in the direction of the grain only.

Toxic Fumes.

 The engine exhaust from this product contains chemicals known to the state of 

California to cause cancer and birth defects and other reproductive harm.

Risk of asphyxiation.

 This engine emits carbon monoxide, an odorless, colorless poison gas. 

Breathing carbon monoxide can cause nausea, fainting or death. Use only in a well ventilated 
area.

Clearance.

 Keep all objects including others at least 10 feet (3m) from this machine. 

Only one person should operate the log splitter and load the logs

Never operate on an incline. Make sure the splitter is on a level surface. Block tires and ensure 
support leg is secure to prevent unintended movement of the log splitter during operation.

MAX.

 45 MPH (72 km/h)

DO NOT

 exceed the maximum 45 MPH (72 KM/H) towing speed.

Always check all local, state or provincial regulations regarding towing, licensing and lights before 
towing your log splitter. Review towing safety warnings in your towing vehicle manual.

In most states towing on public streets is either prohibited or would require further licensing or 
modifications. Please check with your local, state, or provincial authorities regarding regulations, 
restrictions and registration.

Any modifications required to meet these laws are the responsibility of the purchaser.

Summary of Contents for 100330-1











































Reviews: