background image

aXis CONTROLLER HOME STANDBY GENERATOR

INSTALLATION

39

3.  Press TEST button. 

4.  The engine will start and the ATS will transfer.

5.  The aXis Controller screen will indicate that the generator is 

now suppling power to the home.

 

WARNING

The manufacturer recommends that a licensed electrician or 
an individual with complete knowledge of electricity perform 
these tests.

6.  With rated load applied, check voltage and frequency across 

ATS GENERATOR SUPPLY terminals L1 and L2. Voltage must 
be greater than 216 Volts.

7.  Frequency should be greater than 58 Hertz.

8.  Verify that the gas pressure remains within the acceptable 

parameters as listed in the manual, provided that you placed 
a Manometer in line prior to starting this test.

9.  In test mode, the HSB will run under load for 15 minutes at 

which time it will conclude the test and shut off automatically. 
With the unit running listen for unusual noises, inspect for 
vibrations or other unusual items that might reflect a problem.

10. To stop the test prior to automatic shut off, press the Test 

Button in the ATS a second time.

11. The HSB will run through a cool down cycle, shut down and 

return to standby mode.

The test is now complete and the system is in standby mode.

Checking Automatic Operation

To check the HSB system for proper automatic operation, proceed 
as follows:

1.  Turn the ATS utility side breaker OFF.

2.  Engine will start and the ATS will transfer.

3.  Allow the system to go through a complete cycle. 

(Approximately 7 minutes)

4.  To conclude Automatic Operation Check, turn the ATS utility 

side breaker ON.

5.  The HSB will run through a cool down cycle, shut off, and 

return to standby mode.

6.  Replace covers on ATS and HSB that were removed for HSB 

Test and Checking Automatic Operation. This check is now 
complete.

Installing Standby Generator to non-aXis 
Controller ™ ATS

OTE: 

N

This section is only for those looking to install their aXis 
Controller™ HSB to a non-aXis Controller™ ATS that 
supports a two-wire HSB start/stop signal. Please refer to 
the ATS installation manual for instructions on how to wire 
the ATS.

If the aXis Controller™ HSB is being connected to a non-
aXis Controller™ ATS, it will be necessary to use a two-wire 
connection shown below to control the on/off operation of this 
HSB. Note that this will disable some of the aXis Controller™ 
features such as load management, WiFi connectivity, and 
wireless exercise programming.  

TWO-WIRE CONNECTION

A two-wire connection refers to a signal circuit that runs between 
the non-aXis Controller™ ATS and the HSB. When installed in this 
configuration, the HSB will turn on and off based on the signal it is 
receiving from the ATS.

The aXis Controller™ HSB uses pin 2 and pin 11 on the back of 
the aXis Controller™ to control two-wire starting. When pin 11 
(normally 5VDC) is connected to pin 2 (ground), the generator will 
start and will continue to run until pin 11 is disconnected from pin 
2 (ground). When pin 11 is disconnected from pin 2 (ground), the 
HSB will start the cool-down cycle and stop. 

To wire the HSB to be controlled by the two-wire start signal, tap 
into the wires for pin 2 and pin 11 on the HSB and run them to a 
relay (not provided) that will close the circuit when the ATS wants 
the generator to run. Refer to the ATS instructions for the ATS 
logic on how to create the circuit.  

CRANK

FQ2

I_AUX

I_LOP

I_HWT

FQ1

B-

ALARM

STOP

PREHEAT

FUEL

CHARGER

(D+)

B+

~

Rated Supply: 8~36 VDC (5A Max,)

(Terminal 13 and 15)

MAX WORKING VOLTAGE

300 VAC

!

DIP1_ENGINE STOP TIME

DIP2_ENGINE STOP TIME

DIP3_SYSTEM FREQUENCY

DIP4_OIL PRESSURE SWITCH TYPE

DIP5_AVR BOOST

DIP6_ENGINE COOLING TIME

vDIP7_ENGINE COOLING TIME

DIP8_IDLE OR PREHEAT

DIP9_PLC ACTIVE

DIP10_STARTER MOTOR STOP RPM 

1

9

15

10

11

12

13

14

8

7

6

5

4

3

2

ON

9

1

10

8

7

6

5

4

3

2

Summary of Contents for aXis














































Reviews: