To open the door
manually:
The door should be fully
closed if possible. Pull
down on the manual
release handle and lift
the door manually. To
reconnect the door to
the opener, press the
Door Control push bar.
32
Activate the opener with any of the following:
• The Remote Control Transmitter. Hold push
button down until the door starts to move.
• The Door Control. Hold push bar down until the
door starts to move.
• The Outside Keylock or Keyless Entry. (See
Accessories)
When the opener is activated with the safety
reversing sensor installed and correctly aligned:
1. If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop (allowing space for
entry and exit of pets and for fresh air).
4. If the door has been stopped in a partially open
position, it will close.
5. If obstructed while closing, the door will reverse.
6. If obstructed while opening, the door will stop.
7. The garage door will reverse in the closing cycle,
and the opener lights will blink for 5 seconds, when
the invisible beam is broken. If fully open, the door
will not close when the beam is broken. The
sensor has no effect in the opening cycle.
If the sensor is not installed, or is not aligned correctly,
the door won't close from any remote transmitter. You
can close the door with the Door Control, the Outside
Keylock, or Keyless Entry, however, if you activate
them
until down travel is complete. If you release
them too soon, the door will
reverse.
Opener Lights will turn on under the following
conditions: When the opener is initially plugged in;
when the power is interrupted; when the opener is
activated. They will turn off automatically after 4-1/2
minutes or provide constant light when the Light
feature is activated. Lights will also turn on when
someone walks through the open garage door. Bulb
size is 75 watts maximum.
Trolley
Trolley
Release Arm
NOTICE
Manual
Release Handle
(Pull Down)
Trolley
Trolley
Release Arm
NOTICE
Manual
Release Handle
(Pull Down & Back
Towards Opener)
Lockout position
Manual disconnect
position
Weak or broken springs could allow an open
door to fall (either rapidly or unexpectedly),
resulting in serious injury, death or property
damage. If possible, use the manual release
rope and handle
only when door is fully
closed.
Operation of Your Opener
WARNING
The lockout feature
prevents the trolley from
reconnecting automat-
ically. Pull the manual
release handle down
and back (toward the
opener). The door can
then be raised and
lowered manually as
often as necessary. To
disengage the Lockout
Feature, pull the manual
release handle straight
down. The trolley will
reconnect on the next
UP or DOWN operation.
Door Control Push Bar: Press the white square to
open or close the door. Press again to
reverse the door
during the closing cycle or to
stop the door while it's
opening.
Light Feature: Press the Light button. If the opener
light is
off, it will turn on. If the opener light is on, (even
in the 4-1/2 minute automatic cycle) it will turn
off.
But if you use the Light button to turn the lights
on and
then activate the opener, the lights will turn
off after
4-1/2 minutes.
The 4-1/2 minutes interval can be changed to 1-1/2,
2-1/2, or 3-1/2 minutes as follows: Press and hold the
Lock button until the light blinks (about 10 seconds).
A single blink indicates that the timer is reset to 1-1/2
minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes.Repeat again
for a 3-1/2 minute interval, etc., up to a maximum of
four blinks and 4-1/2 minutes.
The Light button will not control the opener lights when
the door is in motion.
Lock Feature: The Lock feature is designed to prevent
operation of the door from remote controls. However,
the door will
open and close from the Door Control
push bar, the Outside Keylock and the Keyless Entry
Accessories.
To Activate: Press and hold the Lock button for
2 seconds. The push bar light will flash as long as
the Lock feature is
on.
To turn off: Press and hold the Lock button again
for 2 seconds. The push bar light will stop flashing.
Normal operation will resume. The Lock feature will
also turn off whenever the “Smart” button on the
opener panel is activated.
Operation of the Multi-Function Door Control
(See additional programming features, next page.)
