background image

Door

Highest Point

of Travel

Header

Wall

Pivot

Distance

Header Wall

Highest Point

of Travel

Door

Distance

Jamb

Hardware

The Chamberlain Group, Inc.
Position Header Bracket
One Piece Door Without Track
1/30/92 - 4/7/92 

Header Wall

Vertical

Centerline

Vertical

Centerline of

Garage Door

2x4

Unfinished

Ceiling

Structural

Supports

2x4

OPTIONAL CEILING MOUNT

FOR HEADER BRACKET

• Close the door and mark the

inside vertical centerline of
your garage door. Extend the
line onto the header wall
above door.

If headroom clearance is
minimal, you can install the
header bracket on the ceiling.
See page 14.

• 

If you need to install the
header bracket on a 2x4 (on
wall or ceiling), use lag screws
(not supplied) to securely
fasten the 2x4 to structural
supports as shown.

Example

Distance from top of door 
(at highest point of travel) to floor...........................92"

Actual height of door .............................................-88"

Remainder................................................................4"

Add .........................................................................+8"

Bracket height on header wall ..............................=12"

(Measure UP from top of CLOSED door.)

Proceed to Step 2, page 14.

13

Door

Highest Point

of Travel

Header

Wall

Pivot

Distance

Header Wall

Highest Point

of Travel

Door

Distance

Jamb

Hardware

The Chamberlain Group, Inc.
Position Header Bracket
One Piece Door Without Track
1/30/92 - 4/7/92 

Header Wall

Vertical

Centerline

Vertical

Centerline of

Garage Door

2x4

Unfinished

Ceiling

Structural

Supports

2x4

OPTIONAL CEILING MOUNT

FOR HEADER BRACKET

Door

Highest Point

of Travel

Header

Wall

Pivot

Distance

Header Wall

Highest Point

of Travel

Door

Distance

Jamb

Hardware

The Chamberlain Group, Inc.
Position Header Bracket
One Piece Door Without Track
1/30/92 - 4/7/92 

Header Wall

Vertical

Centerline

Vertical

Centerline of

Garage Door

2x4

Unfinished

Ceiling

Structural

Supports

2x4

OPTIONAL CEILING MOUNT

FOR HEADER BRACKET

ONE-PIECE Door Without Track

• Open your door to the highest point of travel as

shown. Measure the distance from the top of the
door to the floor. Subtract the actual height of the
door. Add 8" to the remainder. (See Example.)

• Close the door and draw an intersecting horizontal

line on the header wall at the determined height.

If the total number of inches exceeds the height
available in your garage, use the maximum
height possible, or refer to page 14 for ceiling
installation.

One-piece door without track

pivot hardware

One-piece door without track

jamb hardware

Read the Safety Instructions on page 12. They also apply to doors without tracks.

Summary of Contents for Security+ 6200-2K









































Reviews: