manualshive.com logo in svg

Chamberlain MH, Installation Manual

Share
Download
Chamberlain MH Installation Manual Download Page 32

C O N T R O L   C O N N E C T I O N   D I A G R A M

01-34217C 

© 2009, The Chamberlain Group, Inc.

 

All Rights Reserved

IMPORTANT NOTES:

1.  The 3-Button Control Station provided must be connected for operation.
2.  If a STOP button is not used, a jumper must be placed between terminals 3 and 5.
3.  If INTERLOCK is not used a jumper must be placed between terminals 3 and 4.
4.  When adding accessories, install them one at a time and test each one after it is added to ensure proper installation and operation
  with the Commercial Door Operator.

3 BUTTON STATION OR 3 POSITION KEYSWITCH WITH SPRING RETURN TO CENTER AND STOP BUTTON

2 OR MORE

KEY LOCKOUT

7

6

3

5

Stop

Close

Open

Stop

Close

Open

7

6

3

5

Stop

Close

Open

2 BUTTON STATION OR 3 POSITION KEYSWITCH WITH SPRING RETURN TO CENTER

STANDARD

7

6

3

Close

Open

C2

MODE ONLY

2 OR MORE

7

6

3

Close

Open

Close

Open

C2

MODE ONLY

DEVICE TO REVERSE

EXTERNAL INTERLOCK

1

2

3

4

3

4

Remove Factory Installed Jumper

When Interlock is Used

ONE

2 OR MORE

STANDARD

7

6

3

5

Stop

Close

Open

All Wiring Types

Keyswitch

Sensing Device

Note:

 For photo-eyes connection options see

OPTIONAL SAFETY DEVICE CONFIGURATION section.

See note 2.

See note 2.

Summary of Contents for MH

































Reviews:

No comments

Brands by name

Popular brands

Load more brands