manualshive.com logo in svg

Chamberlain MH, Installation Manual

Share
Download
Chamberlain MH Installation Manual Download Page 13

13

A

B

2

ADJUST THE CLUTCH

Clutch Nut

Replace Cotterpin

To Loosen

To Tighten

A D J U S T M E N T

Bend ends 
of cotterpin 
to secure 
clutch nut

• Apply power to operator
• Turn clutch nut to release tension.
•  Re-tighten nut until there is just enough 

tension to permit smooth operation.

• Secure clutch nut with cotter pin.

1

ADJUST THE LIMITS

To avoid SERIOUS personal INJURY or DEATH from 
electrocution, disconnect electric power BEFORE  moving limit 
nuts or adjusting clutch nut.

ATTENTION

AVERTISSEMENT

AVERTISSEMENT

AVERTISSEMENT

WARNING

CAUTION

WARNING

WARNING

WARNING

PRECAUCIÓN

ADVERTENCIA

ADVERTENCIA

ADVERTENCIA

Depress retaining plate

Adjust OPEN limit

Adjust CLOSE limit

Retaining Plate

Decrease Door 
Travel

Increase Door 
Travel

OPEN Limit Switch

OPEN Limit Nut

CLOSE Limit Switch

CLOSE Limit Nut

SAFETY Limit 
Switch

Decrease Door 
Travel

Increase Door 
Travel

NOTE:

 When retaining plate is released, verify that the retaining plate is fully seated with the notches of the limit nut.

Summary of Contents for MH

































Reviews:

No comments

Brands by name

Popular brands

Load more brands