background image

4

TEST

Test the remote control by pressing the button you programmed to control 

the door. If the garage door opener does not activate, repeat the

programming steps, view the programming videos on 

chamberlaindiy.com.au/universal or chamberlaindiy.co.nz/universal or 

contact Customer Service AU: 1800 638 234 NZ: 0800 653 667  

PROGRAMMING THE REMOTE

Start with your garage door closed. Ensure that the door is clear of all 

obstructions.
Press and hold the Bottom Button (for 

approximately 15 seconds) on the 

remote control until the blue LED stays ON 

solid, then release the button. (The blue 

LED will remain ON for 60 seconds).
Press the LEARN button on your garage door opener for 2-3 seconds, 

then release it. 
Immediately Press & Release the remote control button you would like 

to program. The Blue LED will commence blinking for 12 seconds.

Once the Blue LED changes to solid, immediately Press & Release 

the same button on the remote again. The remote will now try to pair 

to the opener.
The Blue LED on the remote control will begin to flash once every three 

seconds while trying to pair to the opener, (this may take up to 60 

seconds). When the door begins moving, 

immediately (within 3 

seconds)

 press the remote button again.

The coding process is complete and your remote should now be 

programmed to the garage door opener.You can repeat this process 

using the other remote button to program another garage door opener.

Blue LED

2

1

3

4

Bottom 

Button

In order to program the Universal Remote, the LEARN button on the 

garage door opener must be located. Please refere to page 3 as well as 

the compatibility table on page 2 for the lean button label used for various

brands.

These are generic instructions for most garage door openers, 

for 

ATA branded openers refer to the instructions on page 5

. Read through 

all steps before commencing, and become familiar with the control buttons. 

Once the programming sequence has commenced its important to 

continue from one step to another reasonably quickly. Time between 

steps is critical.

This is also a good time to view our Instructional videos on our website. 

chamberlaindiy.com.au/universal or chamberlaindiy.co.nz/universal.

5

6

Summary of Contents for MC100AMLR









Reviews: