background image

GARAGE DOOR OPENER WARRANTY

Chamberlain warrants to the first retail purchaser of this product
that the product shall be free from any defect in materials and/or
workmanship for a period of 24 full months (2 years) from the
date of purchase. Upon receipt of the product, the first retail
purchaser is under obligation to check the product for any visible
defects. 

Conditions:

The warranty is strictly limited to the reparation or

replacement of the parts of this product which are found to be
defective and does not cover the costs or risks of transportation
of the defective parts or product.

This warranty does not cover non-defect damage caused by
unreasonable use (including use not in complete accordance
with Chamberlain’s instructions for installation, operation and
care; failure to provide necessary maintenance and adjustment;
or any adaptations of or alterations to the products), labor
charges for dismantling or reinstalling of a repaired or replaced
unit or replacement batteries.

A product under warranty which is determined to be defective in
materials and/or workmanship will be repaired or replaced (at
Chamberlain's option) at no cost to the owner for the repair
and/or replacement parts and/or product. Defective parts will be
repaired or replaced with new or factory rebuilt parts at
Chamberlain's option.

If, during the warranty period, the product appears as though it
may be defective, contact your original place of purchase.

This warranty does not affect the purchaser’s statutory rights
under applicable national legislation in force nor the purchaser’s
rights against the retailer arising from their sales/purchase
contract. In the absence of applicable national or EU legislation,
this warranty will be the purchaser’s sole and exclusive remedy,
and neither Chamberlain nor its affiliates or distributors shall be
liable for any incidental or consequential damages for any
express or implied warranty relating to this product.

No representative or person is authorized to assume for
Chamberlain any other liability in connection with the sale of this
product.

EDR4 8004A

11

C

, 2007 Chamberlain

These declarations are made by:

D e c l a r a t i o n   o f   C o n f o r m i t y

Automatic rolling door openers, as stated, are in conformity to the applicable sections of EN55014-1
(2000), EN55014-2 (1997), EN61000-3-2 (2000), EN61000-3-3 (1995), EN 301 489-3 (V1.3.1), 
EN 300 220-3 (V1.1.1), EN60335-1 (1994), and EN60335-2-95 (2000).

Per the provisions of the European Directives, 89/336/EEC, 2006/95/EC and 1999/5/EC, including all
amendments;
Model:..................................................................................................................................RDO800 

All technical file information for the operator and its accessories is held at The Chamberlain Group and
will be made available at the request of the authorities should the need arise

.

D e c l a r a t i o n   o f   I n c o r p o r a t i o n

A power door operator must not be put into service until it has been completely and safely assembled
and installed, with appropriate size and weight of door, in accordance with both the door and operator
manufacturers’ instructions using appropriate safety devices, and the complete installation has been
declared in conformity with the provisions of EN12453, EN13241-1 and the Machinery Directive,
98/37/EC. 

Door Type: Rolling Door

Operator
Type

Maximum Area
(m2)

Installer: Indicate
Installed Door
Size

Maximum Weight
(kg)

Installer: Indicate
Installed Door
Weight

RDO800

12.0

100

B. P. Kelkhoff
Manager, Regulatory Affairs

Chamberlain GmbH.
D-66793 Saarwellingen
June

, 2007

________________________________________

Installer Name/Signature

________________________________________

Company Name

________________________________________

Address

_____________________________________

Date

Summary of Contents for LiftMaster Professional RDO800 Series















Reviews: