background image

2

When you see these Safety Symbols and Signal
Words on the following pages, they will alert you to
the possibility of 

serious injury or death

if you do

not comply with the warnings that accompany them.
The hazard may come from something mechanical
or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following
pages, it will alert you to the possibility of damage to
your garage door and/or the garage door opener if
you do not comply with the cautionary statements
that accompany it. Read them carefully.

INTRODUCTION

Safety Symbol 
and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated,
maintained and tested in strict accordance with the instructions and warnings contained in this manual.

Mechanical

Electrical

WARNING

CAUTION

WARNING

WARNING

WARNING

CAUTION

WARNING

WARNING

WARNING

CAUTION

WARNING

WARNING

Introduction

2-7

Safety symbol and signal word review........................2

Preparing your garage door ........................................3

Tools needed ...............................................................3

Planning ..................................................................4-5

Carton inventory ..........................................................6

Hardware inventory .....................................................7

Assembly 8-11

Fasten the rail to the motor unit ..............................8, 9

Install the chain and the sprocket cover .....................8

Install the chain spreader and the chain ...................10

Tighten the chain .......................................................11

Installation 11-27

Installation safety instructions....................................11

Determine the header bracket location ................12-13

Install the header bracket..........................................14

Attach the rail to the header bracket.........................15

Position the opener ...................................................16

Hang the opener .......................................................17

Install the door control...............................................18

Install the light and lens ............................................19

Attach the emergency release rope and handle .......19

Electrical requirements..............................................20

Install the Protector System

®

................................21-23

Fasten the door bracket .......................................24-25

Connect the door arm to the trolley .....................26-27

Adjustment

28-30

Adjust the travel limits ...............................................28

Adjust the force .........................................................29

Test the safety reversal system.................................30

Test the Protector System

®

........................................30

Operation  

31-34

Operation safety instructions.....................................31

Using your garage door opener ................................31

Using the wall-mounted door control ........................32

To open the door manually........................................32

Care of your garage door opener..............................33

Having a problem? ....................................................34

Programming

35-36

To add or reprogram a hand-held remote control .....35

To erase all codes .....................................................35

3-Button remotes.......................................................35

To add, reprogram or change
a Keyless Entry PIN ..................................................36

Repair Parts  

37-38

Rail assembly parts ...................................................37

Installation parts ........................................................37

Motor unit assembly parts .........................................38

Accessories

39

Repair Parts and Service

40

Warranty

40

TABLE OF CONTENTS

Summary of Contents for LiftMaster 1345









































Reviews: