Chamberlain LA500UL Installation Manual Download Page 27

Page: 27 / 56

Gate operator setup examples

The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site
requirements, including all necessary entrapment protection devices.

RESIDENTIAL:

One to four residential homes sharing a gated entrance/exit, allowing vehicle access trumps security concerns

COMMERCIAL/GENERAL ACCESS:

A residential community (more than four homes) having one or more gated entrances/exits, allowing vehicle access

trumps security concerns

COMMERCIAL:

Business site where security (gate closed) is important

INDUSTRIAL:

Large business site where security is required

SETTING

RESIDENTIAL

COMMERCIAL/GENERAL
ACCESS

COMMERCIAL

INDUSTRIAL

Quick Close switch
setting

Normally set to OFF. Normal gate
close (timer or control).

Set to ON, so that gate closes
immediately after vehicle passes
CLOSE EYES/Interrupt loop.

AC Fail Open switch
setting

Normally set to BATT. Run on
battery if AC power fails.

Normally set to BATT. For local
jurisdiction requirement, set to
OPEN so that the gate will open
approximately 15 seconds after AC
power fail.

Normally set to BATT. Run on
battery if AC power fails.

Low Battery switch
setting

Normally set to OPEN. If powered
from battery and battery is low,
gate automatically opens and stays
open.

Normally set to CLOSE. If powered
from battery and battery is low,
gate stays closed.

Anti-Tail switch setting

Normally set to OFF. CLOSE
EYES/Interrupt loop reverses a
closing gate.

Set to ON. In attempt to prevent
vehicle tail-gating, CLOSE EYES/
Interrupt loop pauses a closing
gate.

Bipart Delay switch
setting

For DUAL-GATE site, set to ON for
gate that delays upon opening.

Aux Relay Out – Open
Limit Switch

Typically not required.

Use with SAMS (Sequence Access
Management System).

Use with SAMS (Sequence
Access Management
System).

Connect “Gate Open”
indicator (e.g. light).

Use with SAMS (Sequence
Access Management
System).

Connect “Gate Open”
indicator (e.g. light).

Aux Relay Out – Close
Limit Switch

Typically not required.

Connect “Gate Close/Secure”
indicator (e.g. light).

Aux Relay Out – Gate
Motion

Attach alert signal (audible or
visual alert system).

Aux Relay Out – Pre-
Motion Delay

Attach alert signal (audible or
visual alert system).

Aux Relay Out – Power

Attach visual alert to know when
system is charging batteries (i.e.
not running on batteries).

Cycle Quantity Feedback

Use during servicing only to
determine operator cycles.

Fire Dept Open Input

Typically not required.

Connect emergency access
system (Knox box switch, SOS
system, etc.).

Typically not required.

OPERATION

Summary of Contents for LA500UL

























































Search results

Summary of Contents for LA500UL

Reviews:

Chamberlain LA500UL, Installation Manual, Page: 27 / 56

Search results

Summary of Contents for LA500UL

Reviews: