Chamberlain LA500UL Installation Manual Download Page 2

Page: 2 / 56

SAFETY

Safety Symbol and Signal Word Review ...................................................2

Usage Class ..............................................................................................3

UL325 Entrapment Protection Requirements ...........................................3

Safety Installation Information ..................................................................4

Gate Construction Information ..................................................................5

INTRODUCTION

Carton Inventory .......................................................................................6

Operator Specifications .............................................................................7

Site Preparation ........................................................................................8

Check your gate ........................................................................................8

INSTALLATION 9

Installation Tips ........................................................................................9

Step 1 Position the Brackets ...................................................................10

Step 2 Attach the Brackets ......................................................................11

Step 3 Install the Control Box .................................................................12

Step 4 Earth Ground Rod ........................................................................14

Step 5 Wire the Operator Arm to the Control Board ...............................14

Step 6 Dual Gate Setup ...........................................................................15

Step 7 Install Entrapment Protection ......................................................18

Wire Entrapment Protection Devices ......................................................19

Step 8 Power Wiring ...............................................................................20

Step 9 Finish Installation ........................................................................22

ADJUSTMENT 22

Limit and Force Adjustment ....................................................................22

Obstruction Test .....................................................................................24

PROGRAMMING 25

Remote Controls (Not Provided) ............................................................25

LiftMaster Internet Gateway (Not Provided) ...........................................26

Erase All Codes .......................................................................................26

Erase Limits ............................................................................................26

To Remove and Erase Monitored Entrapment Protection Devices ..........26

OPERATION 27

Gate Operator Setup Examples ...............................................................27

Control Board Overview ..........................................................................28

Manual Release .......................................................................................29

Reset Button ...........................................................................................29

Party Mode .............................................................................................29

Operator Alarm .......................................................................................30

Remote Control .......................................................................................30

ACCESSORY WIRING

External Control Devices .........................................................................31

Maglock ..................................................................................................32

Miscellaneous Wiring ..............................................................................32

EXPANSION BOARD

Expansion Board Overview .....................................................................33

Auxiliary Relays 1 and 2 .........................................................................34

Wiring Accessories to the Expansion Board ...........................................35

MAINTENANCE 36

Important Safety Instructions .................................................................36

Maintenance Chart ..................................................................................36

Batteries ..................................................................................................36

TROUBLESHOOTING 37

Diagnostic Codes ....................................................................................37

Diagnostic Codes Table ..........................................................................38

Control Board LEDs ................................................................................40

Troubleshooting Chart ............................................................................41

APPENDIX 44

Installation Types ....................................................................................44

Step 1 Position the Brackets ...................................................................44

Step 8 Solar Panels ................................................................................45

Limit Setup with a Remote Control .........................................................49

SAMS Wiring with the Relays Not Energized ..........................................50

REPAIR PARTS

Standard Control Box ..............................................................................51

Large Metal Control Box .........................................................................51

Gate Operator Arm ..................................................................................51

WIRING DIAGRAM

Standard Control Box ..............................................................................52

Large Metal Control Box .........................................................................53

ACCESSORIES

WARRANTY

When you see these Safety Symbols and Signal Words on the following pages, they will alert

you to the possibility of

Serious Injury or Death

if you do not comply with the warnings that

accompany them. The hazard may come from something mechanical or from electric shock.

Read the warnings carefully.
When you see this Signal Word on the following pages, it will alert you to the possibility of

damage to your gate and/or the gate operator if you do not comply with the cautionary

statements that accompany it. Read them carefully.

IMPORTANT NOTE:

• BEFORE attempting to install, operate or maintain the operator, you must read and fully

understand this manual and follow all safety instructions.

• DO NOT attempt repair or service of your gate operator unless you are an Authorized

Service Technician.

TABLE OF CONTENTS

SAFETY

Safety Symbol and Signal Word Review

MECHANICAL

ELECTRICAL

WARNING:

This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more

information go to

www.P65Warnings.ca.gov.

Summary of Contents for LA500UL

























































Search results

Summary of Contents for LA500UL

Reviews:

Chamberlain LA500UL, Installation Manual, Page: 2 / 56

Search results

Summary of Contents for LA500UL

Reviews: