background image

9

To avoid SERIOUS damage to garage door opener, use ONLY
those bolts/fasteners mounted in the top of the opener.

ASSEMBLY STEP 2

Fasten the Rail to the Motor Unit

• Insert a 1/4"-20x1-3/4 bolt into the cover protection bolt

hole on the back end of the rail as shown. Tighten
securely with a 1/4"-20 lock nut. 

Do NOT overtighten.

• Remove the two bolts from the top of the motor unit.

• Place the “U” bracket, flat side down onto the motor

unit and align the bracket hole with the bolt holes.
Fasten with the previously removed bolts.

• Align the rail assembly with the top of the motor unit.

Slide the rail end onto the “U” bracket,

all the way to

the stops that protrude on the top and sides of the
bracket.

• Attach spreader to the motor unit with two screws.

ASSEMBLY STEP 3

Install the Idler Pulley

• Lay the chain/cable beside the rail, as shown. Grasp

the end of the cable and pass approximately 12" 
(30 cm) of cable through the window. Allow it to hang
until Assembly Step 5.

• Remove the tape from the idler pulley. The inside

center should be pre-greased. If dry, regrease to
ensure proper operation.

• Place the idler pulley into the window as shown.

• Insert the idler bolt from the top through the rail and

pulley. Tighten with a 3/8" lock washer and nut
underneath the rail until the lock washer is
compressed. 

• Rotate the pulley to be sure it spins freely.

• Insert a 1/4"-20x1-3/4 bolt into the trolley stop hole in

the front of the rail as shown. Tighten securely with a
1/4"-20 lock nut.

WARNING

CAUTION

WARNING

WARNING

Bolts

Hex Screws 
8-32x7/16" 

Chain
Spreader

Motor Unit
Sprocket

"U" Bracket

Lock Nut

SLIDE RAIL TO STOPS
ON TOP AND SIDES
OF BRACKET

Cover 
Protection
Bolt Hole

Bolt

Lock
Washer
3/8" 

 Nut 3/8"

Cable Link

Idler
Bolt

Chain and
Cable

Pulley

Rail

Bolt

Nut

Washer

Trolley

Idler
Pulley

Idler
Pulley

Grease
Inside Pulley

Screwdriver

Trolley
Stop Hole

Bolt

Lock
Nut

Lock 

Nu

t

1/4"-20

Bolt 1/4"-20x1-3/4" 

HARDWARE SHOWN ACTUAL SIZE

Nu

t 3/

8

"

Lock 

W

asher 3/

8

"

Idler Bolt

Lock 

Nu

t 1/4"-20

Bolt 1/4"-20x1-3/4"

HARDWARE SHOWN ACTUAL SIZE

Summary of Contents for HD175D 1/2 HP









































Reviews: