background image

32

CARE OF YOUR OPENER

LIMIT AND FORCE ADJUSTMENTS:

Weather conditions may cause some
minor changes in door operation
requiring some re-adjustments,
particularly during the first year of
operation.

Pages 27 and 28 refer to the limit
and force adjustments. Only a
screwdriver is required. Follow the
instructions carefully.

Repeat the safety reverse test
(Adjustment Step 3, page 29) after
any adjustment of limits or force.

FORCE CONTROLS

LIMIT CONTROLS

(Left panel)

(Back panel)

1

3

9

7

5

1

3

9

7

5

Kg

Kg

INCREASE  TRAVEL

DOWN

UP

THE REMOTE CONTROL BATTERY

The lithium battery should produce power for up to
5 years. 

To replace battery, use the
visor clip or screwdriver blade
to pry open the case as shown.
Insert battery positive side 
up (+).

Dispose of old battery properly.

Replace the battery with only
3

V

2032 coin cell batteries.

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.

To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.

WARNING

CAUTION

WARNING

WARNING

MAINTENANCE SCHEDULE

Once a Month

• Manually operate door. If it is unbalanced or binding,

call a trained door systems technician.

• Check to be sure door opens & closes fully. Adjust

limits and/or force if necessary. (See pages 27 and 28)

• Repeat the safety reverse test. Make any necessary

adjustments. (See Adjustment Step 3)

Twice a Year

• Check chain tension. Disconnect trolley first. Adjust if

necessary. (See page 11)

Once a Year

• Oil door rollers, bearings and hinges. The opener does

not require additional lubrication. Do not grease the
door tracks.

Battery 
positi

v

side 

u

p (+)

To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
• Do NOT recharge, disassemble, heat above 212°F (100°C )

or incinerate.

WARNING

CAUTION

WARNING

WARNING

Summary of Contents for HD175D 1/2 HP









































Reviews: