Challenger VKFCSD22IR Series, Manual

Page: 19 / 24

33
MAIN MENU
SYSTEM SETTING
→
CAMERA SETTING
→
FUNCTION SETTING
→
DISPLAY SETUP
→
EXIT
SYSTEM SETTING
EDIT DOME TITLE
→
DOME INFO
→
DOME ID SETTING
→
PASSWORD SETUP
CLOCK SETTING
→
SYSTEM PARAMETER
→
DEFAULTS
→
BACK
EXIT
CAMERA SETTING
LENS PARAMETERS HIGH
AE MODE SETTING ON
AWB MODE SETTING OFF
ADVANCE PARAMETERS
→
PRIVACY MASK
→
BACK
EXIT
DISPLAY SETUP
PRESETS
SCAN
PATTERNS
PATTERN NUMBER 1
RECORD PATTERN
RUN PATTERN
CLEAR PATTERN
EDIT PATTERN TITLE
→
BACK
EXIT
TOUR
ZONES
FUNCTION SETTING
PRESETS
→
SCAN
→
PATTERNS
→
TOUR
→
ZONES
→
BACK
EXIT
DOME TITLE OFF
PRESET TITLE OFF
ZOOM POSITION ON
ZONES NAME OFF
DIRECTION LABEL ON
TEMPERATURE LABEL OFF
TIME LABEL ON
DATE LABEL ON
BACK
EXIT
DEFAULTS
CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL TOURS
CLEAR ALL PRIVACIES
FACTORY DEFAULTS
RESTART
BACK
EXIT
DOME INFO
DOME S/N:
VERSION:
MODEL:
PROTOCOL :FACTORY
DOME ID: 001
BAUD RATE: 4800bps
BACK
EXIT
TITLE: PRE001
BACK
EXIT
EDIT PRESET TITLE
TITLE: SCAN 1
BACK
EXIT
EDIT SCAN TITLE
TITLE: PATTERN-1
BACK
EXIT
EDIT PATTERN TITLE
TITLE: ZONE-1
BACK
EXIT
EDIT ZONE TITLE
TITLE
BACK
EXIT
:
EDIT DOME TITLE
AE MODE AUTO
SHUTTER N/A
IRIS N/A
BRIGHT N/A
BACK
EXIT
AE MODE SETTING
PASSWORD SETUP
LENS PARAMETERS
ZOOM SPEED HIGH
DIGITAL ZOOM OFF
BLC MODE OFF
SLOW SHUTTER OFF
WDR MODE N/A
MIRROR OFF
FLIP OFF
DAY/NIGHT SETTING
→
BACK
EXIT
SCAN NUMBER 1
SCAN SPEED 20
SET LEFT LIMIT
SET RIGHT LIMIT
CLEAR SCAN
RUN SCAN
EDIT SCAN TITLE
→
BACK
EXIT
TOUR NUMBER 1
EDIT TOUR
→
RUN TOUR
CLEAR TOUR
BACK
EXIT
ZONE NUMBER 1
SET LEFT LIMIT
SET RIGHT LIMIT
CLEAR ZONE
EDIT ZONE TITLE
→
BACK
EXIT
PRESET NUMBER 001
SET PRESET
SHOW PRESET
CLEAR CURRENT PRESET
EDIT PRESET TITLE
→
BACK
EXIT
TIME 03:20:18
DATE 07-10-10
DAY WED
BACK
EXIT
CLOCK SETTING
OLD PASSWORD
： ******
NEW PASSWORD
：
******
CONF PASSWORD
：
******
ENABLE PASSWORD
：
OFF
BACK
EXIT
DOME ID SETTING
S/N
：
B866CS000003
CONF ：
DOME ID
：
BACK
EXIT
AWB MODE AUTO
R GAIN N/A
B GAIN N/A
BACK
EXIT
AWB MODE SETTING
SHARPNESS 05
HI-RESOLUTION ON
MAX GAIN 28dB
EXPOS COMP N/A
BACK
EXIT
ADVANCE PARAMETERS
PRIVACY NUMBER 01
EDIT PRIVACY
ENABLE PRIVACY OFF
CLEAR PRIVACY
BACK
EXIT
PRIVACY MASK
SYSTEM PARAMETER
FAN ENABLED 045C
TEMP C/F CENT.
POWER UP ACTION AUTO
EIS ENABELED N/A
PRESET FREEZE OFF
PAN/TILT SETTING
→
TIME ACTION SETUP
→
PARK ACTION SETUP
→
BACK
EXIT
10. Appendix
10. 1 Menu index
Appendix
No action, no
video after
power up
Possible causes Trouble Solution
10. 2 Trouble shooting
Power line connected wrong
Correct
Engineering line is malfunction
Self-testing and
image are normal
but the dome is
uncontrollable
The dome DIP switch setting
is incorrect
Refer to switch setting,reset the switch
Rs485 may carve out a way
Check Rs485connection, confirm
the connection is correct and
good in contact
Rs485 is in malfunction
Pls consult appendix
“
Rs485
Bus acknowledge
”
Video image
is not steady.
Video line is bad connection
Eliminate
Power consumption is not enough
Video image is
not steady and the
motor is faulted
Power consumption is not enough Replace the power
Dome controlling
is not smooth.
Controlling line connected
wrong, or Rs485 loads too
much or the distance of
communication is too far
1.Connect 120 resistance in the dome pan/tilt
that is far from the controller
2.Increase distributor
Ω
Power supply is damage or
power consumption is not
enough
Replace
Replace right power adapter, it is better to put
the switch and power adapter near the dome
To obtain constant clear videos, user should
clean the down cover periodically.
●
Be caution when cleaning, hold the down cover
ring only to avoid direct touch to the acrylic down
cover. The acid sweat mark of fingerprint will corrode
the coating of down cover and scratch on down cover
will cause vague image.
●
Use soft dry cloth or the substitute to clean the inner
and outer surfaces
●
For hand contamination, use neutral detergent. Any
cleanser for high grade furniture is applicable.
10. 3 The cleaning of clear down cover
Check and repair
3 4
Appendix