background image

1.1.2  Service manual

WARNING:
Some pictures in the manual show the shields removed to permit a clearer view. Never
operate the machine with any shields removed.

This service manual has been prepared with the latest service information available at publication. Read

and understand the service manual carefully before doing any service on the machine.
Right-hand and left-hand, as used in this manual, are determined by facing the direction of machine travel

when in use.
Photos, illustrations, and data used were current at the time of printing, due to possible production

changes, the machine can vary slightly. The manufacturer reserves the right to redesign and change the

machine as necessary without notification.

1.1.3  Safety symbol

The safety symbol tells you about a dangerous

area!
Look for the safety symbol in this manual and on

the machine. The safety symbols tell you that

there is important safety instructions in the

manual.

GUID-4C201302-DBD2-4BFB-8D98-1DDED263BD6E-high.jpg [High]

Fig. 2  

1.1.4  Safety messages

The words DANGER, WARNING or CAUTION are

used with the safety symbol. Learn these safety

messages and obey the recommended

precautions and safety instructions.

DANGER:
If you do not obey the recommended
precautions and safety instructions,
DEATH OR INJURY will occur.

WARNING:
If you do not obey the recommended
precautions and safety instructions,
DEATH OR INJURY can occur.

CAUTION:
If you do not obey the recommended
precautions and safety instructions,
INJURY can possibly occur.

GUID-73F05026-C37B-415A-8140-AD939A283378-high.jpg [High]

Fig. 3  

1.1.5  Information messages

The words important and note are not related to personal safety, and are used to give information about

the operation and servicing of the machine.

GUID-96F0DBC2-FDAB-4BE2-A442-8D57B94A81B4 [V1]

GUID-5D9F270E-D748-4741-82B1-BE49B78685F2 [V4]

GUID-E54F7740-C021-42A8-8784-4287BE4356C8 [V4]

GUID-9A909F52-D57E-4C30-8CC7-6FDB6D7E9982 [V3]

1. General

1-4

Articulated Tractor

79036231D

Find manuals at https://best-manuals.com

Summary of Contents for MT945E




















































Reviews: