Challenger MT297 Service Manual Download Page 16 | Manualshive

Page: 16 / 41

Challenger MT297 Service Manual Download Page 16

79028569 A Rev.

01-13

Specifications and Capacities

Pressure..................................................................................................................................... 11,797 kPa (1711 PSI)

Main Hydraulic System

Pump................................................................................................................................. Engine-mounted gear pump

Maximum Output ............................................................................................................... 43.2 l/min (11.4 US gal/min)

Pressure....................................................................................................... Relief valve setting 15,692 kPa (2276 psi)

Rear Linkage

Type...................................................................................................................................................... Three-point hitch

Size ............................................................................................................................................................... Category 1

Control..................................................................................................................................... Position and draft control

Draft Control.......................................................................................................................................... Top link sensing

Lift Capacity at Ball End ................................................................................................................... 1400 kg (3083 lbs)

Lift Capacity at 61 cm (24 in) Ball Ends........................................................................................... 1180 kg (2600 lbs)

Electrical System

System Voltage........................................................................................................................... 12 volt, negative (-) ground

Battery cca at -18 degrees Celsius (0 degrees Fahrenheit) .................................................................................... 781 cca

Charging................................................................................................... 45 amp alternator with internal regulator/rectifier

«
...
14
15
16
17
18
...
»

Summary of Contents for MT297










































Reviews:

No comments