manualshive.com logo in svg

Challenger MT297, Service Manual, Page: 11 / 41

Share
Download
Challenger MT297 Service Manual Download Page 11

Torque Charts

01-8

79028569 A Rev.  

STANDARD TORQUE CHART

Torque Chart for Metric Fasteners (Zinc Coated)

Nominal Size

In mm

Strength Class

ISO 4.6 (4T)

Strength Class

ISO 8.8 (7T)

Strength Class

ISO 10.9 (9T)

Torque Nm (lbf-ft)

Torque Nm (lbf-ft)

Torque Nm (lbf-ft)

Min.

Max.

Min.

Max.

Min.

Max.

M3

0.5 (0.3)

0.7 (0.5)

1.3 (0.9)

1.7 (1.3)

1.8 (1.3)

2.4 (1.8)

M4

1.2 (0.9)

1.6 (1.2)

3.1 (2.3)

4.1 (3.0)

4.3 (3.2)

5.7 (4.2)

M5

2.2 (1.6)

3.0 (2.2)

6.0 (4.4)

8.0 (5.9)

8.5 (6.3)

11.5 (8.5)

M6

4.2 (2.9)

5.0 (3.7)

10 (7.4)

14 (10.3)

14 (10.3)

20 (14.8)

M8

9.5 (7.0)

12.5 (9.2)

25 (18.4)

35 (26)

36 (26)

46 (34)

M10

19 (14)

25 (18)

50 (37)

70 (52)

72 (53)

96 (71)

M12

33 (24)

43 (32)

90 (66)

120 (89)

120 (89)

160 (118)

M20

160 (118)

210 (155)

420 (310)

560 (413)

600 (443)

800 (590)

M24

280 (207)

360 (266)

720 (531)

860 (634)

1000 (738)

1300 (959)

M30

540 (398)

720 (531)

1400 (1033)

1800 (1328)

2100 (1549)

2800 (2065)

M36

950 (700)

1250 (922)

2500 (1844)

3300 (2434)

3600 (2655)

4800 (3540)

Torque Chart for Inch Fasteners (Zinc Coated)

Nominal Size

Strength Class -

Below SAE5 (plain head)

Strength Class

SAE 5

Strength Class

in inches SAE 8

Torque Nm (lbf-ft

Torque Nm (lbf-ft)

Torque Nm (lbf-ft)

Min.

Max.

Min.

Max.

Min.

Max.

1/4

6.8 (5)

8.1 (6)

10.8 (8)

15 (11)

16.2 (12)

21.7 (16)

5/16

13.5 (10)

16.2 (12)

22 (16)

30 (22)

31 (23)

42 (31)

3/8

24 (18)

28 (21)

39 (29)

53 (39)

56 (41)

75 (55)

7/16

41 (30)

46 (34)

64 (47)

85 (63)

91 (67)

121 (89)

1/2

61 (45)

70 (52)

99 (73)

131 (97)

140 (103)

185 (137)

5/8

122 (90)

142 (105)

198 (146)

263 (194)

279 (206)

371 (274)

3/4

217 (160)

250 (185)

350 (258)

464 (342)

495 (365)

658 (485)

7/8

--

--

569 (420)

800 (759)

800 (590)

1071 (790)

1

--

--

847 (635)

1119 (825)

1200 (885)

1580 (1165)

1-1/8

--

--

1051 (775)

1390 (1025)

1681 (1240)

2224 (1640)

1-1/4

--

--

1491 (1033)

1966 (1450)

2386 (1760)

3159 (2330)

1-1/2

--

--

2576 (1900)

3390 (2500)

4121 (3040)

5437 (4010)

Summary of Contents for MT297










































Reviews:

No comments