background image

  

27

  

Customer Helpline 

 01904 727503

www.gardenservicecentre.co.uk

Guarantee

Dear Customer,
In the unlikely event that your device develops a fault, please contact our Customer service 

department on the telephone number shown below.
1. These guarantee terms cover additional guarantee rights and do not affect your statutory 

warranty rights.
Claims must be accompanied by Proof of Purchase. This must be in the form of a Sales receipt 

or Bank statement and must show that the product has been purchased within 1 year prior to the 

claim, from the retailer that it was originally sold to.
2. Our guarantee covers problems caused by material or manufacturing defects, and will result 

in the repair of these defects or replacement of the device with a like for like or similar article. 

Please note that our devices have not been designed for use in commercial, trade or industrial 

applications. Consequently, the guarantee is invalidated if the equipment is used in commercial, 

trade or industrial applications or for other equivalent activities.
3. The following are also excluded from our guarantee:
A) Faults due to accidents, customer misuse, or unauthorized repairs

B) Consumable Parts such as Blades/ /Spark plugs or Filters

C) Failure due to lack of routine maintenance
D) Failure as a result of not using the equipment in accordance with the manual and safety 

instructions
E) The adjustment of cables, drive belts, or recoil starters

4. The guarantee is valid for a period of 1 years starting from the purchase date of the device. 

Guarantee claims should be submitted before the end of the guarantee period within two weeks 

of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee 

period. The original guarantee period remains applicable to the device even if repairs are carried 

out or parts are replaced. In such cases, the work performed or parts fitted will not result in 

an extension of the guarantee period, and no new guarantee will become active for the work 

performed or parts fitted. This also applies when an on-site Service is used.

5. Please keep your sales receipt in a safe place. If the defect is covered by our guarantee your 

device will either be repaired under the terms of guarantee or we will send you a replacement 

device. This device may be re-conditioned or Like for like replacement.

Summary of Contents for PCS38Z




























Reviews: