background image

  

19

  

Customer Helpline 

 01904 727503

www.gardenservicecentre.co.uk

Maintenance and Storage

List of vulnerable parts

Maintenance after each use

1. Air filter 
Dust on the air filter surface can be removed by detaching the engine cover, removing the filter 

and tapping a corner of the filter cover against a hard surface. To clean dirt in the meshes remove 

the cover and brush in petrol. When using compressed air, blow from the inside. To reassemble 

push the cover back into place, press the rim until it clicks.
2. Oiling port 
Detach the chain bar and check the oiling port for clogging.
3. Chain bar 
When the chain bar is dismounted, remove sawdust from the bar groove and the oiling port.
Grease the nose sprocket through the grease port on the tip of the bar.
4. Others
Check for fuel leakage and loose fastenings and damage to major parts, especially handle joints 

and chain bar mounting and Silencer. If any defects are found, make sure to have them repaired 

before operating the unit again.

Description

Models or specifications

Spark Plug

LD L8RTF/902700

Guide bar

160SDEA041

Saw chain

PJ057X

Clutch drum

910221

WARNING!

 

Before cleaning, inspecting or repairing your unit, make sure that the engine has stopped and is 
cool. Disconnect the spark plug to prevent accidental starting.

Summary of Contents for PCS38Z




























Reviews: