manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 67

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

2-55 

2. Status Indicator RAPs

 

RAP 2.47 Book Entering CMT Sensor 

Input 21 

The book entering CMT sensor is a retro-reflec-
tive sensor that detects books as they enter into 
the trimmer.  The sensor and the reflector are 
mounted on the left side of the trimmer (Figure 
2-72). 

Possible Fault Indicators 

 

“JAM – Book Between Sensor 
Error”

 message is displayed when 

there is no book jam. 

 

If book jam occurs every cycle even 
though the book is pushed in straight, 
go to RAP 2.33 Internal Conveyor Mo-
tor. 

 

If a book jam occurs every cycle be-
cause the book is entering crooked, 
check machine setup in the 

Installation 

and Operator's Manual.

 

Initial Actions 

Check that the reflector on the left side of the 
trimmer below the conveyor belt is installed.  Re-
place reflector if necessary (PL 5.14 Main As-
sembly 59000 (14/14)).   

Check for loose or damaged wire 45 at the elec-
trical panel. 

Check that the internal conveyor motors run.  If 
one or both never run, go to RAP 2.33 Internal 
Conveyor Motor. 

Procedure 

1.  Make sure that both the sensor and the re-

flector are not obstructed.  Switch the main 
power ON and go to the diagnostic screen 
(GP 6.2 Input/Output Diagnostics). Does the 

diagnostic screen show input “Book Entering 
CMT” switched on? 

Y  N 

Short wire 45 to 74 at the main PWB.  On 
the diagnostic screen does input "Book En-
tering CMT" switch on? 

Y  N 

Disconnect power and replace the con-
sole PWB (REP 4.24 Console PWB Re-
placement). 

Adjust the sensor (GP 6.6 Retro-reflective 
Sensors) and replace if faulty (PL 5.17 
Power Panel EE-3503 (2/2)). 

2.  Disconnect wire 45.  On the diagnostic 

screen does input "Book Entering CMT" 
switch off? 

Y  N 

Disconnect power and replace the console 
PWB (REP 4.24 Console PWB Replace-
ment). 

3.  Adjust the sensor (GP 6.6 Retro-reflective 

Sensors) and replace if faulty (PL 5.17 
Power Panel EE-3503 (2/2)). 

 

 

Figure 2-72. Book Entering CMT Sensor 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands