manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 53

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

2-41 

2. Status Indicator RAPs

 

RAP 2.33 Internal Conveyor Motor 

Output 22 

The motor that drives the two internal conveyors 
is located beneath the left-hand conveyor near 
the front of the machine (Figure 2-50).  

Possible Fault Indicators 

 

The internal conveyor motor does not 
run after gripper presets. 

 

The internal conveyor motor runs contin-
uously while a book is in process. 

Initial Actions 

Check for loose or damaged drive belts. 

If motor coasts to a stop (rather than stop 
quickly), check brake wiring and/or replace the 
brake. 

Procedure (conveyors never run) 

1.  Check circuit breaker CB4 and reset if 

tripped.  If CB4 continues to trip, check 
brake wiring and/or replace the brake. 

2.  Check for proper wiring at the terminal 

blocks located on top of the conveyor motor 
brackets (Figure 2-51). 

3.  Switch the main power ON and press the 

green start button to initialize the trimmer.  
Once the hydraulic motor is running, short 
wire 26 to 37 at SSR1. Do both conveyor 
motors switch on? 

Y  N 

Disconnect power and replace the defective 
motor and/or brake (PL 5.11 Main Assembly 
59000 (11/14)). 

4.  Remove the short, then go to the diagnostic 

screen (GP 6.2 Input/Output Diagnostics) 
and enable outputs. Make sure all doors are 

closed, then activate the Interlock Relay out-
put.  Press the green start button to energize 
the IR relay.  The “Interlock Relay IR” input 
should switch on.  Activate the “Conveyor” 
output.  Do the conveyor motors switch on? 

Y  N 

Disconnect power and replace the main 
PCB (REP 4.23 Main PWB Replacement). 

5.  Disconnect power and replace the bad relay, 

SSR1 (PL 5.16 Power Panel EE-3503 (1/2)). 

Procedure (conveyors always run) 

1.  Switch the main power ON and press the 

green start button.  Do the conveyors start 
running continuously without stopping? 

Y  N 

Normal 

2.  Is output LED 22 (GP 6.3 Input/Output 

LEDs) switched on? 

Y  N 

Disconnect power and replace the bad relay, 
SSR1 (PL 5.16 Power Panel EE-3503 (1/2)). 

3.  Disconnect power and replace the main 

PCB (REP 4.23 Main PWB Replacement). 

 

 

Figure 2-50. Internal Conveyor Motor 

 

Figure 2-51. Conveyor Motor Wiring 

 

Figure 2-52. CB4 and SSR1 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands