manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 234

 

 

 

MAY 2019 

 

6. General Procedures/Information

 

6-20 

CMT-130TC Book Trimmer 

GP 6.17 Book Size Chart 

The physical parts of a book are defined as fol-
lows and will be referenced as such throughout 
this manual.  Book dimensions are referenced 
as 

“spine length” x “top (or bottom) edge length”. 

Spine:

  The edge of a book where the pages 

are bound together. 

Top edge:

  Also known as the head, the top 

edge is the edge of the book that is facing away 
from the reader. 

Bottom edge:

  Also known as the foot, the bot-

tom edge is the edge of the book that is facing 
toward the reader. 

Face:

  The face or fore-edge is the edge of the 

book from which it is opened. 

Book block:

  A book block is the printed and 

collated pages of a book that does not include 
the cover.  It contains all front and end matter as 
well as the text block. 

Untrimmed book:

  An untrimmed book is a 

book block that has been bound with a cover but 
has not yet been trimmed to finish size. 

Trimmed book:

  A trimmed book has been 

bound and trimmed to a finish size. 

The charts on Figure 6-19 can be used to deter-
mine if a specific book layout can be trimmed by 
the CMT-130TC.  Using the trimmed spine 
height (h) and the bottom trim (x), make sure the 
desired book size falls within the shaded region 
of the chart.  The overall untrimmed and 
trimmed book dimensions must also be less 
than the maximum allowed (See GP 6.16 Speci-
fications). 

The CMT-130TC software will not allow a book 
to be trimmed outside this range.  The operator 
should be aware of these size constraints before 
books are printed. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure 6-19. Book Size Charts 

 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands