manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 233

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

6-19 

6. General Procedures/Information

 

GP 6.16 Specifications 

WARNING 

The CMT-130TC was designed specifically 
for use with the Challenge infeed and exit ac-
cessories.  If any other accessories are used, 
it is the purchaser's responsibility to comply 
with ANSI B65.4 Safety Standard for Three-
Knife Trimmers.  Failure to comply with this 
standard could result in personal injury or 
death. 

CAUTION 

The CMT-130TC was specifically designed to 
trim perfect bound books only.  Trimming 
other materials with the CMT-130TC may result 
in safety hazards or damage to the machine. 

For trimmable book sizes, see GP 6.17 Book 
Size Chart. 

Multiple Book Mode:  Note that up to 3 books 
may be stacked in multiple book mode.  The to-
tal thickness is not to exceed 1-1/4 in. (32 mm).  
Larger pile thicknesses may be cut, but the trim 
may be less accurate and more out-of-square.  
Always test before running books outside the 
published specifications. 

 

Sound Emission: 

A-weighted sound pressure level measured in 
an enclosed room at operator level (6 feet/183 
cm): 
Machine in idle state: 62 dB 
Machine trimming: 75 dB 

NOTE:  Challenge reserves the right to make 
changes to any product or specification without 
notice and without incurring responsibility to ex-
isting units. 

 

Description 

US Units 

Metric Units 

Max. start book 

13.00 (spine) x 9.50 in. 

330.2 (spine) x 241.3 mm 

Min. start book, off-line (Hand-Feed) 

7.00 (spine) x 5.00 in. 

177.8 (spine) x 127.0 mm 

Min. start book, near-line (Pile Feeder) 
 

7.00 (spine) x 5.00 in. (single book mode) 

7.00 (spine) x 6.75 in. (multi-book mode) 

177.8 (spine) x 127.0 mm 
177.8 (spine) x 171.4 mm 

Min. start book, in-line (Tilt + Elevator) 

7.00 (spine) x 6.75 in. (single book mode) 

7.00 (spine) x 7.00 in. (multi-book mode) 

177.8 (spine) x 171.4 mm 
177.8 (spine) x 177.8 mm 

Min. finish book 

5.82 (spine) x 4.00 in. 

147.8 (spine) x 101.6 mm 

Max. finish book 

12.00 (spine) x 9.00 in. 

304.8 (spine) x 228.6 mm 

Max. face (fore-edge) trim  

5.50 in. 

139.7 mm 

Max. top (head) trim 

6.00 in. 

152.4 mm 

Book thickness range 

0.10 to 2.00 in. 

2.5 to 50.8 mm 

Min. Trim 

0.10 in. 

2.5 mm 

CMT-130TC Basic Machine 

Width 

52 in. 

132 cm 

Depth 

57 in. 

145 cm 

Height 

60 in. 

152 cm 

Net Weight 

1,500 lb. 

680 kg 

Shipping Weight 

1,800 lb. 

816 kg 

Floor Loading 

53 PSI 

3.7 kg/cm

2 

Optional Waste Bin Capacity 

43 gal. 

164 L 

Oil Capacity 

5 gal. 

19 L 

Air Consumption 

5 CFM @ 90 PSI 

142 LPM @ 620 kPa 

Knife Re-grind 

1/4 in. 

6.4 mm 

Memory 

99 jobs 

Time to change book size 

10 sec. or less 

Throughput 

up to 200 books/hr. (single book mode) 

up to 500 books/hr. (multi-book mode) 

Electrical Requirements 

 

60 Hz Machines 

60 Hz, AC, 3 phase, 208/230 Volts, 20 Amps (service size 30 Amps) 

50 Hz Machines 

50 Hz, AC, 3 phase, 380/415 Volts, 16.5 Amps (service size 20 Amps) 

50 Hz, AC, 3 phase, 200-208 Volts, 20 Amps (service size 30 Amps) 

56600TCA Tilt Infeed Conveyor 

(150 lb/68 kg net) (230 lb/105 kg ship) (5.62 PSI/.40 kg/cm

2

 load)

 

Height x Width x Depth 

26 x 39 x 29 in. 

66 x 99 x 74 cm 

Compatible binder exit heights: 

17 to 26 in. 

43 to 66 cm 

56421TCA Cooling Elevator 

(335 lb/152 kg net) (470 lb/214 kg ship) (11.86 PSI/.83 kg/cm

2

 load) 

Height x Width x Depth 

46 x 38 x 22 in. 

117 x 97 x 56 cm 

58500TCA Book Pile Feeder 

(370 lb/168 kg net) (420 lb/191 kg ship) (13.1 PSI/.92 kg/cm

2

 load) 

Height x Width x Depth 

54 x 21 x 57 in. 

137 x 53 x 145 cm 

59200 Standard Hand Feed Conveyor 

(40 lb/18.2 kg net) (80 lb/36.4 kg ship) (3.2 PSI/.22 kg/cm

2

 load) 

Height x Width x Depth 

11 x 16 x 15 in. 

28 x 41 x 38 cm 

56413B Long Hand Feed Conveyor 

(95 lb/43 kg net) (220 lb/100 kg ship) (7.6 PSI/.53 kg/cm

2

 load) 

Height x Width x Depth 

42 x 35 x 13 in. 

107 x 89 x 33 cm 

58000TCA Vertical Stacker 

(218 lb/99 kg net) (268 lb/122 kg ship) (7.7 PSI/.54 kg/cm

2

 load) 

Height x Width x Depth 

44 x 19 x 49 in. 

112 x 48 x 124 cm 

56420TCA Exit Conveyor 

(85 lb/39 kg net) (210 lb/95 kg ship) (6.76 PSI/.48 kg/cm

2

 load) 

Height x Width x Depth 

39 x 47 x 13 in. 

99 x 120 x 33 cm 

59093 Exit Ramp 

(6 lb/ 3 kg net) 

Height x Width x Depth 

5 x 10 x 12 in. 

13 x 25 x 30 cm 

 
Note: See Operator’s Manual for floor space requirements of the CMT-130TC with various option configurations. 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands